Contact Us

VBP165R12

Brand: VBsemi
VBsemi VBP165R12 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP165R12 — Discrete & Power Semiconductors | Superb Automation

VBP165R12

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP165R12 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP165R12: 650 V and 12 A in a TO247 with 800 milliohm

The VBP165R12 is a single N channel MOSFET in a TO247 body rated at 650 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 12 A of drain current and 800 milliohm at a 10 V gate. The vendor table lists the die as planar. It is the smallest member of the 650 V TO247 band and the one that appears where a 650 V part is needed but the current is modest.

Planar is the older structure and it is still the right one at low current. A planar cell has a wider pitch, so the channel resistance per unit area is higher than a trench cell, but the process is simpler, the gate charge is lower for the same area, and the die is cheaper per wafer pass. At 12 A and 800 milliohm the die area needed is small enough that the cost of a trench process is not repaid.

The 800 milliohm figure is the whole story of this part. At 12 A the die makes 115 W, which no TO247 can pass to a heatsink at that current. At 6 A it makes 29 W, at 3 A 7 W. The usable continuous current is therefore 3 to 5 A on a plate heatsink, and the 12 A label describes the die at a 25 C case rather than a working condition.

Key data for the VBP165R12

ConfigurationSingle N channel
PackageTO247, through hole, tab on the drain
VDS650 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID12 A, a die figure at a 25 C case
RDS(on) at 10 V800 milliohm
StructurePlanar
Loss at 3 A7.2 W
Loss at 6 A28.8 W
Loss at 9 A64.8 W
Loss at 12 A115 W

What a low current 650 V part is for

Not every 650 V switch carries the main current. A converter has an auxiliary supply that runs the gate drivers, the control board and the fans, and that supply is 5 to 30 W. It sees the same 400 V bus, so it needs the same voltage class, but it draws 100 to 300 mA. A 12 A part at 800 milliohm is oversized on current and correctly sized on voltage, and it costs less than a 60 A part used at 200 mA.

The second place it appears is a snubber or clamp. An active clamp across a transformer primary holds the leakage spike and conducts for a few microseconds per cycle. The average current is small and the peak is set by the leakage inductance, so a 650 V part with modest on resistance and a low gate charge is a better fit than a large die with high capacitance.

The third is a startup or bypass path, where the switch is on for a fraction of the cycle and off the rest. In that mode the conduction loss is the average current squared times the resistance times duty, and a part at 800 milliohm with 0.1 duty is a 1 W device at 3 A.

Planar against trench in this class.

The choice is not a quality question. A planar cell at 650 V has a wider pitch, which means lower gate charge per unit of on resistance and a lower reverse transfer capacitance for the same die area. In a flyback at 60 kHz with 30 W of load, the switching loss of a planar part can be a third of a trench part of the same resistance, because the gate has less charge to move and the drain voltage swings with a smaller displacement current.

The counter argument is die area. To reach 800 milliohm a trench part needs maybe 60 percent of the die area of a planar part, and area is cost. At 12 A the difference is a few cents on the part and it does not repay a change of source, which is why the band still exists.

For a buyer, the practical point is that a 650 V planar part and a 650 V superjunction part are not interchangeable on a bill of materials even when the voltage and current match. The superjunction die has a much lower resistance at the same current, and a driver that was tuned for the slower planar part will ring harder on the faster one. The pin to pin cross reference page covers which parameters have to match before a swap is signed off.

Switching behaviour and the gate

At 12 A and 650 V this part is a slow switch by modern standards. The turn off time is in the region of 30 to 60 ns with a 10 ohm gate resistor, and the drain voltage dv/dt at 20 to 30 V per ns puts a displacement current through the Miller capacitance that a weak driver cannot sink. A 10 V gate drive through 10 ohms is enough at 20 kHz and marginal at 100 kHz.

The 3.5 V threshold is high enough that a 0 V gate holds the part off in the presence of a few volts of source bounce, which is the reason the part is used in half bridge auxiliaries where the source sits on a switching node. A 1.5 V threshold part in the same place would need a negative off bias to stay off.

Gate charge is the number to check before a swap. Two parts at 800 milliohm can differ by a factor of two in total gate charge, and on a 100 kHz rail the driver loss and the switching loss both follow that number.

Where this part fits

Auxiliary and bias supplies for 400 V bus converters, active clamps on flyback and forward stages, startup bypass paths, and the high side of a low power half bridge where the current is under 3 A. It is also used as the series pass element in a high voltage linear pre-regulator, where the dissipation is set by the drop rather than the load.

It is not the part for a 500 W power factor stage, a motor drive at 5 A continuous, or anything that has to carry more than 4 A in a sealed box. The on resistance decides that, not the current label.

On a production line, the failure mode to watch is a part that was substituted for a superjunction die on the same bill of materials. The voltage and the current match, the resistance is five times higher, and the board works on the bench and fails in the field after 200 hours at full load.

The sourcing side of this part is covered on the component lead time solutions. For a small part that sits on several boards, that page covers how one code is held instead of re-bought.

Questions we get on this code

Why is the 4.5 V resistance column empty? Because the vendor table prints one resistance column at a 10 V gate for this die. The 4.5 V figure is not published, so a board that drives the gate at 5 V has to treat 800 milliohm as an untested number rather than a datasheet value.

Is 650 V enough for a 400 V three phase bus? No. A 565 V DC bus with regeneration reaches 700 V and above, so the class is 900 V or 1200 V. This part belongs on a single phase bus at 325 to 400 V.

Can the same footprint take a superjunction part later? Yes, the TO247 pinout is standard, but the driver and the snubber are not. A faster die in the same body turns a quiet board into one that fails radiated emissions, and re-qualifying the board for emissions is part of the change.

How much margin is left at 12 A? Thermal margin only. At 12 A the die makes 115 W and the junction is past its limit on any heatsink a TO247 can use, so the printed current is a maximum die rating rather than a working point.