Contact Us

VBP165C50

Brand: VBsemi
VBsemi VBP165C50 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP165C50 — Discrete & Power Semiconductors | Superb Automation

VBP165C50

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP165C50 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP165C50: 650 V silicon carbide with a 40 milliohm die

The VBP165C50 is a single N channel silicon carbide MOSFET in a TO247 body. Drain to source is 650 V, the gate window is minus 4 V to plus 22 V, the threshold is 2 to 5 V, the printed drain current is 50 A and the on resistance is 40 milliohm at an 18 V gate. The structure is listed as silicon carbide.

The gate window is the unusual feature. Minus 4 V to plus 22 V is asymmetric in a way that most of this family is not: the negative side stops at 4 V, which is exactly the bias a fast bridge wants for turn off. A driver set to minus 5 V would exceed the rating by 1 V, and a driver that rings below minus 4 V on a fast edge would exceed it by more. This part needs a negative bias that is clamped rather than assumed.

The page also disagrees with itself on current. The table prints 50 A and the text prints a maximum drain current of 40 A. At 50 A and 40 milliohm the die makes 100 W, at 40 A it makes 64 W, so the table figure is already beyond what the package removes and the text figure is the more conservative one. Neither is a socket current.

Key data for the VBP165C50

ConfigurationSingle N channel
PackageTO247, bolted to a heatsink
VDS650 V
VGEMinus 4 V to plus 22 V, a narrow negative side
Vth2 to 5 V
ID50 A in the table, 40 A in the page text, to be confirmed on the data sheet
RDS(on) at 18 V40 milliohm
TechnologySilicon carbide
Loss at 10 A4 W
Loss at 15 A9 W
Loss at 25 A25 W
Loss at 50 A100 W

A minus 4 V gate window changes the driver

The negative gate rating is the limit for the off state, and 4 V is tight. A gate driver with a minus 5 V rail, which is common for silicon carbide, is already outside the window before any ringing is counted. A driver with a minus 2 or minus 3 V rail sits inside with 1 to 2 V of margin, which a short gate loop can hold and a long one cannot.

An alternative is a unipolar drive with an active pull down to zero and a resistor from gate to source. The Miller current at 650 V is smaller than at 1200 V, so a zero volt off state can be adequate if the loop is short and the gate resistor is chosen for the turn off the converter needs. The risk is a gate that floats if the driver loses power, which is why the pull down resistor belongs on the board rather than in the driver.

On the positive side 22 V allows an 18 V drive with 4 V of headroom and a 20 V drive with 2 V. An 18 V rail with a clamp is the usual choice, because the resistance is specified at 18 V and the extra 2 V buys little.

Thermal arithmetic at 650 V

At 25 A the loss is 25 W at the cold resistance and 40 to 50 W at 125 C. A TO247 on a 0.5 to 0.7 C per watt path holds 40 to 50 W with the case near 85 C and the junction near 125 C, so 20 to 25 A is the top of the realistic range and 15 A is comfortable. The 50 A column is a die figure that no sink in a real product reaches.

The switching term at 650 V is smaller than at 1200 V and it is still present. At 400 V bus and 100 kHz the output capacitance term is about 1 to 2 W at 20 A, and the crossover term with a 20 ns edge is similar. A soft switched topology removes most of it, and a hard switched one should be calculated rather than assumed.

The body diode is a factor in a bridge. Its forward drop at 20 A is about 3 to 4 V, which is 60 to 80 W during the dead time, so the dead time has to be tens of nanoseconds and an external SiC Schottky is the usual parallel path. In a converter without a dead time, as in a synchronous buck that keeps one device on, the diode never conducts and the question does not arise.

Where the part fits and where it does not

It fits a 400 V bus inverter at 15 to 25 A, a server supply, an on board charger, a compact drive at 100 kHz, a power factor stage and a phase shifted bridge with a clamped negative bias. It does not fit a 690 V line, a driver with a minus 5 V rail, a 50 A continuous load, or a board that cannot guarantee the gate stays inside minus 4 V.

Where a part with this window is offered as a replacement for another 650 V silicon carbide code, the negative rail is the first thing to check, because a driver that was correct for a minus 10 V window is out of specification here. Our incoming inspection plan page covers what is measured on each lot when a new wide bandgap line enters the store.

The sourcing side of this part is covered on the supplier scorecard. For a line with a narrow gate window, that page covers how the source is scored and watched over time.

Questions we get on this code

Can the gate be driven with minus 5 V off? No. The window stops at minus 4 V, so a minus 5 V rail is out of specification before any ringing is counted.

Is the current 50 A or 40 A? The table prints 50 A and the text prints 40 A. Neither is a socket current, and we record the discrepancy rather than choosing.

Is 40 milliohm the hot figure? No. It is a 25 C value at 18 V, and at 125 C it is roughly double.

What does the order carry? Part number, TO247, tube packing and the date code. We confirm both on the offer.