Contact Us

VBP15R50S

Brand: VBsemi
VBsemi VBP15R50S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP15R50S — Discrete & Power Semiconductors | Superb Automation

VBP15R50S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP15R50S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP15R50S: 500 V and 50 A with 80 milliohm in a TO247

The VBP15R50S is a single N channel MOSFET in a TO247 body rated at 500 V drain to source, plus or minus 30 V on the gate, a 3.8 V threshold, 50 A of drain current and 80 milliohm at a 10 V gate. The die is SJ multiple epitaxy.

Five hundred volts is a class that appears in two places: a 400 V DC bus with a modest margin, and a 380 V three phase line after rectification at about 540 V, where it is 40 V short. The second case is why the class is unusual and why most three phase products use 600 V or 650 V parts instead. For a 400 V bus with a good clamp, 500 V is enough and the resistance is lower than a 650 V part of the same area.

A 3.8 V threshold is high for this band and it is the number that decides the driver. At 3.8 V the gate needs a solid 10 to 12 V to reach the printed 80 milliohm, and a 5 V logic output would sit barely above threshold with the part in a resistive state.

Key data for the VBP15R50S

ConfigurationSingle N channel
PackageTO247, bolted to a heatsink
VDS500 V
VGSPlus or minus 30 V
Vth3.8 V typical
ID50 A, a die figure at a 25 C case
RDS(on) at 10 V80 milliohm
TechnologySJ multiple epitaxy
Loss at 5 A2 W
Loss at 10 A8 W
Loss at 20 A32 W
Loss at 50 A200 W

Two hundred watts at the printed current

At 50 A and 80 milliohm the die makes 200 W, which no TO247 can remove, even on a large sink with a fan. The printed current is a die rating at a held case temperature, and the thermal resistance from junction to case alone limits a TO247 to about 100 W at a 25 C case and far less in a real enclosure.

At 20 A the loss is 32 W, which a 0.6 C per watt path holds with the junction 19 C above the case, so a case at 85 C leaves the die at 104 C. That is a working point. At 10 A the loss is 8 W and the part is comfortable on a modest extrusion. At 5 A it is 2 W and the package is not the question any more.

The gap between 20 A and 50 A is where the choice sits. Above 30 A the part needs two devices in parallel or a larger package, and the resistance of a single die at 500 V cannot be lowered enough to change that. The catalogue current column is not a promise about the socket.

A 500 V part on a 400 V bus

A 400 V DC bus is nominally 400 V and in practice is 410 to 420 V at high line, plus a switching spike that depends on the loop inductance and the diode recovery. With a 500 V part that leaves 80 to 90 V for the spike, which is enough in a well laid out converter and not enough in a sloppy one. The margin rule of 15 to 20 per cent puts 500 V at the edge for a 400 V bus.

The place where 500 V is clearly right is a 380 V AC drive that rectifies to 540 V, no: that line needs 600 V or more. The right place is a converter fed from a 300 to 350 V DC source, a battery at 350 V, a solar string at 400 V open circuit, or a power factor stage with a 390 V output and a clamp. In those circuits 500 V is enough and the lower resistance is a real gain.

Where the bus can be disconnected while the converter is running, or where a motor can regenerate, the rail rises and the 500 V part is no longer safe. Adding a brake chopper or a clamp changes the answer, and the clamp voltage becomes part of the margin calculation rather than an accessory.

Where the part fits and where it does not

It fits a 350 V battery converter, a 400 V solar boost, a power factor stage with a 390 V output, a half bridge in a 5 kW inverter, an induction heating supply at 20 A, and a discharge path on a 400 V bank. It does not fit a 380 V three phase line at 540 V, a 20 A continuous load without a sink, or a driver that cannot supply 12 V at the gate.

Where a 600 V or 650 V code is being replaced by this part to gain resistance, the check is on the surge and the clamp, because 100 to 150 V of margin is what is being traded away. Our power management cross reference page covers how the voltage margin and the resistance are weighed together before a substitute is offered.

The sourcing side of this part is covered on the BOM consolidation. For a 500 V part used across several boards, that page covers how the codes are merged without losing margin.

Questions we get on this code

Is 500 V enough for a 400 V bus? Only with a good clamp and a short loop. The margin is 80 to 90 V, which a sloppy loop can eat in ringing.

Can it run at 50 A? No. Two hundred watts has no path out of a TO247. Twenty amps on a proper sink is the working point.

Is the 3.8 V threshold a problem? It needs a 10 to 12 V driver. A 5 V logic output is not enough and would leave the part resistive.

What does the order carry? Part number, TO247, and tube packing. We confirm the packing and the date code on the offer.