Contact Us

VBP110MR12

Brand: VBsemi
VBsemi VBP110MR12 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBP110MR12 — Discrete & Power Semiconductors | Superb Automation

VBP110MR12

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBP110MR12 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBP110MR12: 1000 V, 0.88 ohm and a 12 A rating that needs a heatsink to mean anything

The VBP110MR12 is a 1000 V N channel power MOSFET in the TO-247 body with an isolated central mounting hole. The product summary prints three numbers: 1000 V from drain to source, 0.88 ohm at a 10 V gate and 170 nC of maximum gate charge. Those three describe a planar high voltage die rather than a super junction one, and the rest of the sheet follows: a threshold window of 3.0 V to 4.0 V, 500 pF of input capacitance, and switching times in the tens of nanoseconds measured at 2 A.

At 1000 V the part sits at the top of the off line range. A 400 V bus with a reflected flyback voltage of 120 V and a 150 V leakage spike lands near 670 V, and 1000 V leaves 330 V for a surge. The same rating suits an auxiliary supply that runs from a 600 V to 800 V rail, a pre charge switch ahead of a large capacitor bank, and a discharge switch on a bus that has to fall before a cover may be opened.

The 0.88 ohm decides whether the part fits at all. At 3 A it sheds 7.9 W, at 6 A it sheds 31.7 W, and at the 12 A continuous rating it sheds 126.7 W. The first is a small heatsink, the second is a real one, and the third needs the case held at 67 C. A buyer who reads only the current column will size the heatsink for the wrong thermal boundary and find out at the first thermal cycle.

The body is TO-247 with a metal tab at drain potential, so an insulating pad is needed unless the heatsink floats, while the central hole is isolated so the screw head does not carry the drain. Mounting torque is 1.1 N m, and the sheet allows 300 C at the leads for 10 s, which is a hand soldering figure rather than a reflow one.

The parameter table in full

Drain to source voltage1000 V
Gate to source voltage, continuousplus or minus 30 V
On resistance at 10 V gate and 2 A0.88 ohm typical
Gate threshold at 250 microamp3.0 V minimum, 4.0 V maximum
Gate leakage at 30 Vplus or minus 100 nA
Drain leakage at 800 V, 25 C and 125 C100 microamp and 500 microamp
Forward transconductance at 2 A5.4 S minimum
Input, output and reverse transfer capacitance500, 250 and 84 pF
Total gate charge at 10 V, 400 V and 2 A170 nC maximum
Gate source and gate drain charge20 and 110 nC
Turn on delay and rise time at 500 V and 2 A19 and 35 ns typical
Turn off delay and fall time, same conditions60 and 36 ns typical
Internal drain and source inductance5.0 and 13 nH
Continuous source drain diode current12 A
Pulsed diode forward current36 A
Body diode forward drop at 2 A1.8 V maximum
Body diode recovery time4 ns typical
Body diode recovery charge3.5 microcoulomb typical, 5.3 maximum
Single pulse avalanche energy, 40 mH and 6.1 A600 mJ
Repetitive avalanche current and energy6.0 A and 19 mJ
Maximum power dissipation, case at 25 C190 W
Linear derating factor1.5 W per C
Junction to case and junction to ambient0.65 and 40 C per watt
Peak diode recovery slope1.0 V per ns
Operating junction and storage rangeminus 55 to plus 150 C
Peak soldering temperature for 10 s300 C

What the two thermal rows allow on a real board

The 190 W dissipation row is the thermal path restated, not an independent limit. 190 W through 0.65 C per watt is 123.5 C of rise, which lands exactly on the 150 C junction from a 25 C case, and the 1.5 W per C derating factor is the same 190 W spread over the same 125 C.

In still air the ambient row takes over and the numbers collapse. 40 C per watt allows 3.125 W for a 25 C room, which through 0.88 ohm is 1.88 A. In a 50 C cabinet the figure is 2.5 W and 1.68 A. The 12 A continuous row at a 25 C case sheds 126.7 W and needs a heatsink that holds the case at 67 C, so the two rows are describing two different products: a bolted part and a part standing on its own copper.

The sheet also prints no hot on resistance row, only the 25 C figure and a normalized curve. A 1000 V planar die typically doubles between 25 C and 150 C, so a calculation that uses 0.88 ohm at operating temperature is optimistic by a factor of two before any heatsink choice is made. We budget on the curve, not on the headline.

The avalanche row and the diode rows do not agree

The avalanche energy is printed as 600 mJ against a stated test of 40 mH and a 6.1 A start. Half of 40 mH times 6.1 A squared is 744 mJ, so the stated test stores more than the row claims. That is the safe direction, unlike three of the 650 V sheets in this shipment where the printed energy is far above what the test can store, but it still means the row cannot be used to size a snubberless flyback without the test report behind it.

The diode rows contradict each other outright. Recovery time is printed as 4 ns and recovery charge as 3.5 to 5.3 microcoulomb. Charge is current multiplied by time, so 5.3 microcoulomb inside 4 ns implies 1325 A of peak reverse current on a 12 A device. One of the two rows is a copy error, and our reading is that the charge row is real because it matches the 0.8 to 1.8 V forward drop and the diode current rows of the same table, while the time row looks like it came from a much smaller die.

The peak diode recovery slope of 1.0 V per ns is the lowest figure in this shipment and describes a slow planar diode. A phase node that rings at 20 V per ns will exceed it, so a 1000 V stage built around this part needs a snubber across the diode or a clamp on the primary, and the recovery charge is the number to size the snubber around.

Where a 1000 V, 0.88 ohm part still earns its place

A 15 W auxiliary supply at 100 kHz, a pre charge switch into a 2200 microfarad bank, a capacitor discharge path, and the upper switch of a two switch forward all fit inside the envelope, because none of them runs the part near its current rating. The two switch forward is the best of the four, since the body diode never conducts there and the slow recovery costs nothing.

Where the part does not fit is any continuous conduction stage above roughly 4 A in still air, and any bridge at 400 V, because the diode recovery charge and the low allowed slope both belong to a part that expects a clamp. A customer who asks for 1000 V and 5 A in a sealed box is better served by a different body with a lower thermal resistance, not by a larger heatsink on this one.

Our power management cross reference work keeps the avalanche energy, the recovery charge and the threshold window on file for every alternate we approve, because those three are what separate two 1000 V parts that print the same voltage and a similar on resistance.

Questions we answer before a reel is booked

First, the gate. 110 nC of gate drain charge against 20 nC of gate source charge is the shape of a high voltage die: the Miller plateau is long and it is where the switching loss lives. A 0.3 A driver needs 170 nC divided by 0.3 A, 570 ns, to move the gate from rail to rail, so the driver and the external resistor set the loss and the 35 ns rise time belongs to the 6.2 ohm condition in the table, not to the circuit on the board.

Second, the threshold. A window of 3.0 V to 4.0 V with a 5 V driver leaves 1 V of margin at cold, which is not enough for a 1000 V stage where the drain moves 800 V in 35 ns. Drive it from 10 V to 12 V and check the 0.8 ohm internal gate resistance against the external resistor so the turn on delay does not stretch.

Third, the alternate. A 1000 V part at 0.8 to 1.0 ohm comes in TO-247 from several suppliers with different recovery charge and different threshold, and the two are not interchangeable in a snubbered stage. We hold both on file per approved alternate and the incoming inspection plan checks the incoming lot against them, while the pin to pin comparison starts from the tab, the lead spacing and the isolated hole, since a body with an isolated hole will not take the screw a plain tab needs.