Contact Us

VBN1603

Brand: VBsemi
VBsemi VBN1603 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBN1603 — Discrete & Power Semiconductors | Superb Automation

VBN1603

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBN1603 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBN1603: 60 V, 2.8 milliohm and a 210 A row that the leads cannot carry

The VBN1603 is a 60 V N channel trench MOSFET in the TO-262 body, 2.8 milliohm at a 10 V gate, a 210 A continuous rating at a 25 C case and a 375 W dissipation row. It also prints a continuous source current of 120 A with a package limited note, and that note is the most important line on the page.

A 210 A die in a three lead leaded body cannot pass 210 A through its leads. The source row of 120 A is the leadframe limit, and any circuit that needs more than that has to parallel devices or move to a different package, whatever the drain row says. The sheet is honest about it, which is more than many competitor sheets are.

The rest of the page is a low voltage, high current switch: 60 V covers a 48 V rail with 12 V of margin, the 2.8 milliohm keeps the conduction loss low at 50 A to 100 A, and the 175 C junction gives room in a sealed enclosure.

The parameter table in full

Drain to source voltage60 V
Gate to source voltage, continuousplus or minus 20 V
On resistance at 10 V gate and 30 A, 25 C0.0028 ohm typical
On resistance at 4.5 V gate and 20 A0.0040 ohm typical
On resistance at 10 V gate and 30 A, 125 C and 175 C0.0060 and 0.0080 ohm
Gate threshold at 250 microamp1.5 V minimum, 2.0 V typical, 2.5 V maximum
Continuous drain current, case at 25 C and 125 C210 A and 120 A
Continuous source current, package limited120 A
Pulsed drain current480 A
Single pulse avalanche current into 0.1 mH75 A
Single pulse avalanche energy281 mJ
Maximum power dissipation, case at 25 C and 125 C375 W and 125 W
Junction to ambient, board mounted40 C per watt
Junction to case0.4 C per watt
Operating junction and storage rangeminus 55 to plus 175 C
Zero gate voltage drain current at 60 V and 25, 125 and 175 C1, 50 and 350 microamp
On state drain current at a 10 V gate120 A
Forward transconductance at 30 A109 S
Input capacitance, typical and maximum at 25 V7300 and 9125 pF
Output capacitance, typical and maximum935 and 1170 pF
Reverse transfer capacitance, typical and maximum647 and 810 pF
Total gate charge, typical and maximum at 110 A184 and 276 nC
Gate source and gate drain charge24.7 and 50.4 nC
Gate resistance, minimum, typical and maximum0.5, 1.1 and 1.6 ohm
Turn on delay and rise time at 30 V and 110 A19 and 23 ns typical, 29 and 35 maximum
Turn off delay and fall time, same conditions83 and 35 ns typical, 125 and 53 maximum
Pulsed source drain diode current480 A
Body diode forward drop at 100 A0.9 V typical, 1.5 V maximum

125 W at a 125 C case, and what that means for the leads

The derating from 375 W at a 25 C case to 125 W at 125 C follows the 0.4 C per watt junction to case path with a 175 C limit, and the numbers close: 250 W times 0.4 is 100 C of rise, which is exactly the case step. This sheet's thermal table can be used as printed.

At 100 A the loss at 25 C is 28 W, and the case rises 11 C through the 0.4 C per watt path, so the part runs cool on metal. At 120 A, the source limit, the loss is 40.3 W and the case rises 16 C. At 210 A, which the die can take, the loss is 123 W, the case rises 49 C, and the leads are the limit long before the silicon.

Above 120 A the leads are the limit, and the sheet says so in the source row. Two devices in parallel share the current and halve the resistance, and the 0.4 C per watt path stays the same per device, so a 200 A stage is two of these on one heatsink rather than one device at twice the current. In still air the 40 C per watt row allows 3.75 W for the 150 C rise, which is 36.6 A at 25 C resistance. That is a large current for a leaded body in still air, and it comes from the very low resistance rather than from a special package.

Gate charge of 276 nC at 110 A sets the driver

This is the row that decides the gate drive. 276 nC maximum at a 10 V gate and 110 A of drain current means the driver has to deliver 0.276 W of gate energy per switching event at 1 kHz, or 2.76 W at 10 kHz, and the peak current during the miller plateau is set by the plateau voltage over the total gate resistance. With 1.6 ohm on the die, a 2 ohm external resistor halves the available drive and doubles the switching time.

The 50.4 nC of gate drain charge against 24.7 nC of gate source charge says most of the charge goes into the drain swing, which is what a low voltage, high current die looks like. The 83 ns turn off delay with a 35 ns fall at 110 A is slow in absolute terms, and at 100 kHz that is a meaningful fraction of a 10 microsecond period.

The input capacitance maximum of 9125 pF against a 7300 pF typical is a 25 percent spread. A driver sized on the typical will be marginal on the slow lots, and the 276 nC maximum already includes that spread on the charge side.

Where a 60 V, 2.8 milliohm part fits

A 48 V telecom rectifier output, a battery disconnect for a 48 V pack, a synchronous rectifier in a 24 V output, a brushless motor bridge leg and a hot swap stage all sit inside the envelope. In each case the switch carries a high current for most of the period, so the 2.8 milliohm decides the loss and the 120 A lead limit sets how many devices are needed.

For a 100 A load the leads are at 83 percent of their limit, so a single device works but with no margin for a fan failure. For a 150 A load two devices in parallel are the right answer, and the 2.8 milliohm at 25 C becomes 1.4 in parallel. Paralleling needs matched thresholds, and the 1.5 V to 2.5 V window on this sheet is tight enough that lot matching is practical.

Where a customer is comparing this part with a 60 V device in a different body, the row that matters is the source current limit, not the drain row. Our power management cross reference work records the package limit for every alternate, because a 210 A die in a 120 A leadframe is a 120 A part.

Questions we answer before a reel is booked

First, the lead limit. 120 A through the source is a package ceiling, and it is printed with the package limited note on the drain row as well. Ask for the lead temperature rise at the current the board will carry, and derate from 120 A rather than from 210 A.

Second, the gate drive. 276 nC maximum is a heavy gate, and the 10 V level is not optional at these currents because the 4.5 V resistance is 43 percent higher. A driver with 2 A peak and a 2 ohm series resistor gives a switching time the board can survive; a 10 A driver with no resistor gives an edge that rings.

Third, the second source. 60 V parts at 2.8 milliohm differ in gate charge and in the resistance at temperature, and a substitute with the same cold resistance can be 40 percent worse at 175 C. The incoming inspection plan and the pin to pin comparison hold the hot resistance and the charge per approved alternate.