Contact Us

VBMB18R20S

Brand: VBsemi
VBsemi VBMB18R20S is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBMB18R20S — Discrete & Power Semiconductors | Superb Automation

VBMB18R20S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBMB18R20S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBMB18R20S: 800 V and 20 A with 205 milliohm in a TO220F

The VBMB18R20S is the largest die of the 800 V TO220F group: 800 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 20 A of printed drain current and 205 milliohm at a 10 V gate, in an isolated plastic tab body. The die is SJ multiple epitaxy.

Two hundred and five milliohm is the lowest resistance in this 800 V body and it is bought with area. At 20 A the die makes 82 W, at 10 A it makes 20.5 W, at 6 A it makes 7.4 W, at 4 A it makes 3.3 W. Compared with the 11 A member of the band at 350 milliohm, the saving at 6 A is 5.2 W, which is the difference between a small heatsink and a large one.

The class rules do not change with the die size. Eight hundred volts holds a 480 V AC line at 680 V with 120 V of margin and a 400 V bus with a large margin, and it does not hold a 690 V line or a 600 V bus with a heavy surge.

Key data for the VBMB18R20S

ConfigurationSingle N channel
PackageTO220F, isolated plastic tab
VDS800 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID20 A, a die figure at a 25 C case
RDS(on) at 10 V205 milliohm
TechnologySJ multiple epitaxy
Loss at 4 A3.3 W
Loss at 6 A7.4 W
Loss at 10 A20.5 W
Loss at 20 A82 W

When the bigger die is worth its price

At 4 A the gap between this part and the 350 milliohm member is 2.3 W. On a 2 C per watt sink that is 5 C of junction temperature, which no one needs. At 6 A the gap is 5.2 W and the junction difference is 10 C, which is the difference between a 100 C die and a 110 C die in a 60 C box. At 8 A the gap is 9.2 W and the smaller die needs a fan.

The price of the larger die is not only the part cost. It carries more gate charge, so the driver has to deliver more current at the same switching time, and it has more output capacitance, so the turn on loss in a discontinuous converter is larger. At 65 kHz those terms are small; at 200 kHz they can cancel the conduction saving.

The decision rule is the thermal one. If the smaller die already runs below 100 C at the highest ambient, the larger die is wasted money. If it runs at 120 C, the larger die is cheaper than a bigger sink and a fan, and it is the correct buy even at a higher unit price.

There is one more entry in the price of the larger die that does not appear on any quotation. The bigger area makes the solder joint under the tab more critical, because a void of the same size removes a smaller share of the contact but the watts are higher. A reflow profile checked on the smaller die does not transfer to the larger one without an x ray on the first articles.

The isolated tab and the loss budget

A plastic tab TO220F is about 2 to 3 C per watt junction to case, so 7.4 W at 6 A lifts the die 15 to 22 C above the sink and 20.5 W at 10 A lifts it 40 to 60 C. A sink at 70 C therefore allows 6 A comfortably and 10 A only with a large extrusion and airflow.

Soldered to a copper island the path is different and often better for a few watts, because the island spreads heat into the board and the vias carry it to the opposite layer. A 600 square millimetre island on two ounce copper holds 3 to 5 W in still air, which is 4 to 5 A for this part, and the enclosure decides how much of that leaves the box.

The plastic tab has one advantage that the table cannot show: it can be bolted to a live heatsink without an insulator, and in a product with several high side devices on one extrusion that removes a washer, a grease step and a failure mode. Where the sink is grounded anyway, a metal tab part with an insulator is the better thermal choice and the same electrical result.

Where the part fits and where it does not

It fits a 480 V AC flyback at 100 to 300 W, a power factor stage at 200 to 400 W, an auxiliary supply in a 690 V drive, a half bridge in a small inverter, and a discharge path on a 400 V capacitor bank. It does not fit a 690 V line, a 20 A continuous load in a plastic tab, or a 200 kHz converter at more than 4 A.

Where this part is used to replace several smaller codes at one voltage, the check is that the highest surge in the group stays inside the 800 V margin and that the gate drive is strong enough for the larger die. Our BOM consolidation page covers how a band is reduced to one code without losing the second source.

The sourcing side of this part is covered on the safety stock planning. For the largest die in a family, that page covers how much is held against a build that depends on one code.

Questions we get on this code

Is 205 milliohm low enough for a 300 W supply? Yes at 4 to 6 A. At 10 A the plastic tab becomes the limit before the die does, and a metal tab or a larger package is the better answer.

Can it run at 20 A? Not continuously. Eighty two watts cannot leave this body. Six amps on a heatsink is realistic.

Is the gate drive different from the smaller die? Yes, it needs more charge for the same transition time, so the driver current and the gate resistor have to be checked rather than copied.

What does the order carry? Part number, TO220F, tube packing and the date code. We confirm both on the offer.