Contact Us

VBMB1402

Brand: VBsemi
VBsemi VBMB1402 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBMB1402 — Discrete & Power Semiconductors | Superb Automation

VBMB1402

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBMB1402 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBMB1402: 40 V and 180 A with 3 milliohm in a TO220F

The VBMB1402 is a single N channel MOSFET in a TO220F body, the fully isolated version of the TO220 with a plastic tab instead of a metal one. Drain to source is 40 V, the gate window is plus or minus 20 V, the threshold is 3 V, the printed drain current is 180 A, and the on resistance is 3 milliohm at both the 4.5 V and the 10 V gate columns. The die is listed as trench.

A flat 3 milliohm at both gate voltages is unusual and it is the most interesting number on the page. It says the channel is fully enhanced by 4.5 V, so the part behaves the same on a 5 V rail and on a 10 V rail, and the drive voltage stops being a variable in the loss arithmetic. Most parts at this resistance print 5 or 6 milliohm at 4.5 V, and that difference is the reason a driver upgrade is often unnecessary with this die.

Forty volts puts the part on a 24 V bus with a transient margin, on a 12 V rail with a large margin, and on the output of a two stage converter that runs at 24 to 36 V. It does not put it on a 48 V battery, where the charged pack reaches 54 V and the switching spike goes higher.

Key data for the VBMB1402

ConfigurationSingle N channel
PackageTO220F, isolated plastic tab
VDS40 V
VGSPlus or minus 20 V
Vth3 V typical
ID180 A, a die figure at a 25 C case
RDS(on) at 10 V3 milliohm
RDS(on) at 4.5 V3 milliohm
TechnologyTrench
Loss at 20 A1.2 W
Loss at 60 A10.8 W
Loss at 180 A97.2 W

What the isolated tab costs and what it buys

A TO220F replaces the copper tab with a plastic one, so the thermal path from die to heatsink goes through the plastic and the resistance rises. A metal tab TO220 is typically 1 to 1.5 C per watt junction to case, and the isolated body is roughly 2 to 3 C per watt. For the same 10 W the die runs 20 to 30 C hotter.

What it buys is a mounting that needs no insulating washer and no thermal grease between the tab and the sink, and a tab that can be bolted to a live heatsink without a short. In a product where several devices share one extrusion that is worth more than the degrees, because the assembly step disappears and the risk of a punctured pad goes with it.

The choice is therefore not thermal alone. If the sink is at ground and the drain sits at 24 V, a metal tab needs an insulator, a shoulder washer and a torque spec. If the sink is isolated, the metal tab is better on every count. On a board with a copper island, neither matters and the isolated body is the easier part to place.

Loss and current in a 40 V part

At 3 milliohm the conduction loss at 20 A is 1.2 W, at 40 A it is 4.8 W, at 60 A it is 10.8 W and at the printed 180 A it is 97 W. The 180 A figure belongs to a die at a held case temperature and it is not reachable in a plastic tab body on a board. A working range for a copper island is 15 to 25 A, and for a bolted heatsink 30 to 50 A.

Switching loss adds to this and it is not in the table. At 24 V and 20 A with a 20 ns crossover the overlap loss is about 0.1 W per switch transition at 100 kHz, which is small against 1.2 W. At 60 A it becomes 0.3 W, still small. This part is a conduction part, and its loss profile rewards a low frequency, high current circuit.

The body diode also matters in a synchronous buck. Its forward drop at 20 A is around 0.7 V for the dead time, which is 14 W for the duration of the dead time. That is why the dead time has to be short and why the diode is not a substitute for the low side switch being on.

Where the part fits and where it does not

It fits a 24 V brushed motor driver, a 12 V battery disconnect, a synchronous buck low side at 20 A, a load switch on a 24 V industrial rail and a reverse polarity protection stage on a 24 V input. It does not fit a 48 V pack, a 400 V bus, or a current near the printed figure in this body.

Where several codes at this voltage are already on a BOM, the isolated body and the flat resistance curve make this part a candidate for consolidation, and the comparison has to include the thermal penalty of the plastic tab rather than only the electrical table. Our BOM scrubbing page covers how duplicated codes at one voltage are reduced without losing a second source.

The sourcing side of this part is covered on the incoming inspection plan. For a part bought in volume, that page covers what is measured on each lot before it reaches the line.

Questions we get on this code

Is the tab really isolated? Yes, the body is TO220F with a plastic tab rated for the full voltage, so no washer is needed and the sink can be live.

Why is 4.5 V the same as 10 V? The channel is fully enhanced by 4.5 V on this die. It means a 5 V gate driver reaches the printed resistance, which is rare at this current level.

Can it carry 180 A? Not in this body. Ninety seven watts has no path out of a plastic tab. Expect 20 to 50 A depending on the sink.

What does the order carry? Part number, TO220F, and tube packing. We confirm the packing on the offer.