Contact Us

VBM1806

Brand: VBsemi
VBsemi VBM1806 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBM1806 — Discrete & Power Semiconductors | Superb Automation

VBM1806

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBM1806 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBM1806: 80 V and 120 A with 6 milliohm in a TO220

The VBM1806 is a single N channel MOSFET in a TO220 body rated at 80 V, plus or minus 20 V on the gate, a 3 V threshold, 120 A of drain current, 6 milliohm at a 10 V gate and 14 milliohm at 4.5 V. It is the same voltage class as the VBM1803 and sits roughly one die size below it, which is the way a catalogue band is built: one voltage, several die areas, several resistances, one package.

The gap between the two gate columns is the largest in this band, 6 milliohm against 14, a factor of 2.3. That is the signature of a die with a thin channel, and it tells the reader that the drive voltage is not a detail on this part but the parameter that decides whether it works. A 10 V driver gets the printed loss. A 4.5 V driver gets more than twice the loss and a die that runs hot for no reason.

At 120 A and 6 milliohm the die makes 86 W. At 50 A it makes 15 W. At 30 A it makes 5.4 W. At 20 A it makes 2.4 W. Only the last two figures belong on a board with a copper island instead of a heatsink.

Key data for the VBM1806

ConfigurationSingle N channel
PackageTO220, through hole with the tab on the drain
VDS80 V
VGSPlus or minus 20 V
Vth3 V typical
ID120 A, a die figure at a 25 C case
RDS(on) at 10 V6 milliohm
RDS(on) at 4.5 V14 milliohm
TechnologyTrench
Loss at 20 A2.4 W at 6 milliohm
Loss at 30 A5.4 W at 6 milliohm
Loss at 50 A15 W at 6 milliohm

Choosing between this part and the next die size up

The VBM1803 prints 3 milliohm and this part prints 6 at the same 80 V and in the same body. At 30 A the difference is 2.7 W against 5.4 W, which is a real difference on a copper island and a small one on a heatsink that is already removing 20 W. At 15 A it is 0.7 W against 1.4 W, which no normal board notices.

That is the rule for choosing inside a band: the larger die pays for itself only when the current is high enough that the saved watts matter, and the saved watts matter only when the thermal path is the limit. On a heatsink with margin, the smaller die is the cheaper part and the same circuit. On a sealed enclosure with a copper island, the larger die is worth its price.

A second difference that does not appear in the table is the gate charge. The larger die carries more charge at the same gate voltage, so a weak driver turns it on more slowly. At 100 kHz that can cost more in switching loss than the conduction figure saves. The charge curve is not on the catalogue page, so it has to be requested before a frequency is fixed.

Thermal arithmetic on a through hole body

A TO220 bolted to a 2 C per watt heatsink with a thermal pad holds 5.4 W with the junction about 19 C above the sink, so a 70 C sink leaves the die at 89 C and there is margin. Fifteen watts on the same sink lifts the junction 45 C above the sink, which needs a sink below 60 C to stay inside the limit. That is a fan, not a passive extrusion.

Soldered flat to a copper island the numbers are lower and less certain. The island spreads heat sideways, the board carries some of it to the opposite layer through vias, and the enclosure decides how much leaves the board. A working figure for a 600 square millimetre island on two ounce copper is 2 to 3 W in still air, which puts this part at 18 to 22 A continuous.

Nothing in the table warns about this. The current column is a die rating at a case temperature that is held by a tester, and the resistance is a die parameter at 25 C. Both are honest and neither is a thermal solution.

Where the part fits and where it does not

It fits a 48 V input buck at 10 to 20 A, a 24 V motor driver in a handheld tool, a battery reverse polarity switch on a 48 V pack, an LED driver on a 36 V rail and a load switch on a 60 V battery system. It does not fit a 100 A continuous load in this body, a rail above 80 V with transients, or a board that can only offer a 5 V gate drive.

For a purchasing decision the resistance at the real gate voltage, the thermal path and the second source all have to be settled before a part is written into a BOM, because a substitution made on the headline current alone is the usual reason a first article runs hot. Our how to reduce component cost page covers where a smaller die, a second source or a changed package actually saves money.

The sourcing side of this part is covered on the strategic sourcing. For one code used across several boards, that page covers how the source is held rather than re-bought.

Questions we get on this code

Why is the 4.5 V figure more than double the 10 V figure? The channel is thin at this die size, so the gate voltage has a large effect on resistance. It is normal for the class and it is the reason the driver matters.

Can this part replace the VBM1803? In a circuit below 15 A, usually yes with margin. Above 30 A the extra 3 milliohm becomes watts and the thermal path has to be rechecked.

Is a heatsink required? Above about 10 W yes, and below that a copper island is enough if it is large and the enclosure is not sealed.

What does the order carry? Part number, TO220, and tube or reel packing. We confirm the packing on the offer.