VBM16R32S
Product Specifications
VBM16R32S
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM16R32S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM16R32S: 600 V and 32 A at 85 milliohm
The VBM16R32S is a single N channel MOSFET in a TO220 body rated at 600 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 32 A of drain current and 85 milliohm at a 10 V gate. The die is listed as SJ multiple epitaxy.
This is the largest of the three 600 V dies in this band, the one that carries the highest current and the most gate charge. At 85 milliohm it is the part to choose when the load is near 15 A and the enclosure can remove the heat, and it is the wrong part when the load is 3 A and the switching loss matters more than the conduction loss.
Eighty five milliohm at 32 A is 87 W. At 20 A it is 34 W. At 15 A it is 19 W. At 10 A it is 8.5 W. The working current on a clip on heatsink with airflow is 15 to 20 A.
Key data for the VBM16R32S
| Configuration | Single N channel |
| Package | TO220 through hole with a metal tab |
| VDS | 600 V |
| VGS | Plus or minus 30 V |
| Vth | 3.5 V |
| ID | 32 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 85 milliohm |
| Technology | SJ multiple epitaxy |
| Loss at 10 A | 8.5 W at 85 milliohm |
| Loss at 20 A | 34 W at 85 milliohm |
| Loss at 32 A | 87 W at 85 milliohm |
| Gate charge | Not printed, ask for the curve at the working drain voltage |
Where the largest die stops paying
From 110 to 85 milliohm is a quarter less conduction loss, which at 15 A is 6 W on a part making 25 W. That is worth having. The cost is a larger gate charge and a larger output capacitance, both of which scale with die area and both of which show up at the switching frequency.
At 325 V and 40 kHz the capacitance loss of a die this size can be 3 to 4 W, against perhaps 2 W on the smaller die. The net gain at 15 A is still positive. At 5 A the conduction saving is 0.6 W and the capacitance penalty is larger than that, so the smaller part is the better one.
The crossover moves with the bus voltage, because the capacitance loss scales with the square of the voltage. At 400 V the larger die pays less often than at 325 V, and at a 200 V bus it pays almost always.
Driving a large die at thirty hertz to fifty kilohertz.
The gate charge of a die this size needs a driver of at least an amp to keep the transition short, and the gate resistor sets the transition time against the ringing. At 325 V with a fast diode the balance is usually 10 to 15 ohm, and a value chosen for a smaller die makes the part slow and hot.
The 30 V gate window allows a 12 V drive with 18 V of margin, which is comfortable at this voltage. A negative off bias is not usually needed outside a bridge, but a hard pull down is, because a large die has a large drain to gate capacitance and the Miller current at turn off is proportional to it.
Where two parts are paralleled to share a 30 A load, the thresholds have to be matched and the sources need a small resistor each. At 85 milliohm a 10 milliohm source resistor is 12 per cent of the total, which is the price of sharing.
Heat removal at 19 watts
At 15 A the loss is 19 W and a TO220 tab on a clip on heatsink with a silicone pad holds it at a case 19 degrees above the heatsink. With a 60 C heatsink and a 1 degree per watt junction to case the junction sits near 80 C, which is comfortable on a 150 C device.
At 20 A the loss is 34 W and the heatsink needs airflow, or the part moves to a TO247 where the case to heatsink path is better. At 32 A the loss is 87 W and the package is out of its depth whatever the heatsink, because the junction to case resistance alone gives a 87 degree rise.
The tab is the drain at the bus voltage, so the insulator is a safety part and the heatsink is live without it. The creepage from the tab to the mounting screw and to any earthed metal is part of the mechanical drawing, not an afterthought.
Where the part fits and where it does not
It fits a 230 V front end at 15 to 20 A, a bridge leg in a 1 kW inverter, a boost converter on a 325 V bus and a motor drive at 400 V and a few kilowatts. It does not fit a 3 A load where the capacitance loss dominates, a 480 V AC input, or a 32 A continuous load in a TO220.
For a large die at 600 V the questions are the switching frequency, the driver current and the heat the enclosure can remove. Our BOM shortage recovery page covers what happens when the part a build was planned around cannot be bought and a substitute has to be qualified in a week.
The sourcing side of this part is covered on the BOM consolidation. For a build that uses several dies at one voltage, that page covers how the ladder of codes is reduced without losing margin.
Questions we get on this code
Is it better than the 110 milliohm part? Above about 12 A yes, below it the extra capacitance cancels the gain. Choose on the working current, not on the label.
Can it carry 32 A? At 87 W, no. Fifteen to twenty amps with a heatsink and airflow is the working range.
How much gate drive does it need? An amp at least, with 10 to 15 ohm in the gate, to keep the transition short at 325 V.
What should a purchase order carry? Part number, TO220, and the packing the line can take. We confirm the tube quantity on the offer.