VBM16R25SFD
Product Specifications
VBM16R25SFD
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM16R25SFD from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM16R25SFD: 600 V and 25 A at 110 milliohm
The VBM16R25SFD is a single N channel MOSFET in a TO220 body rated at 600 V drain to source, plus or minus 30 V on the gate, a 3.5 V threshold, 25 A of drain current and 110 milliohm at a 10 V gate. The die is listed as SJ multiple epitaxy.
It sits between the 150 milliohm 20 A part and the 85 milliohm 32 A part in the same 600 V class, and the three codes together are a ladder of die area at one voltage. The choice between them is made on the working current and on the heat the enclosure can remove, not on the label.
One hundred and ten milliohm at 25 A is 68.75 W. At 15 A it is 24.75 W. At 10 A it is 11 W. At 5 A it is 2.75 W. The working current on a clip on heatsink is 10 to 15 A.
Key data for the VBM16R25SFD
| Configuration | Single N channel |
| Package | TO220 through hole with a metal tab |
| VDS | 600 V |
| VGS | Plus or minus 30 V |
| Vth | 3.5 V |
| ID | 25 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 110 milliohm |
| Technology | SJ multiple epitaxy |
| Loss at 5 A | 2.75 W at 110 milliohm |
| Loss at 10 A | 11 W at 110 milliohm |
| Loss at 25 A | 68.75 W at 110 milliohm |
| Gate charge | Not printed, ask for the curve at the working drain voltage |
A ladder of die area at one voltage
Three parts at 600 V with 150, 110 and 85 milliohm are three die sizes on one voltage platform. Each step up costs gate charge and capacitance and buys conduction loss, and the point on the ladder where a product belongs is where the conduction loss is about half of what the heatsink can remove.
Below that point the extra die area is wasted on a load that runs cool anyway, and the extra gate charge makes the switching loss worse. Above it the part runs hot and the margin disappears on a warm day. The 110 milliohm step is the middle of the three and it fits a converter at 8 to 15 A.
The three parts also differ in capacitance, which sets the energy lost at every turn on. A larger die at a high bus voltage loses more in that path, so the gain in conduction at low current can be cancelled by the loss in capacitance. That is why the smallest die is sometimes the better part at 3 A.
Multiple epitaxy in a bridge.
The multiple epitaxy structure gives a body diode with a softer recovery than a deep trench die, which matters in a hard switched bridge. The recovery loss is spread over a longer time, so the voltage spike is lower and the opposite device sees less stress.
The trade is a slightly higher resistance per unit area, which is why the 110 milliohm part is larger than the deep trench part at 150 milliohm. For a bridge at 20 kHz the softer diode is often worth the extra silicon.
In a flyback the diode only conducts during the dead time and the softness matters less. There the deep trench part with the lower resistance for the area is the better choice, and the frequency is set by the transformer rather than by the diode.
Heat removal at 11 watts
At 10 A the loss is 11 W and a TO220 tab on a clip on heatsink with a silicone pad holds it at a case about 11 degrees above the heatsink. At 15 A it is 24.75 W and the heatsink needs airflow. At 20 A it is 44 W and the package wants a TO247 or a pair of devices.
The tab is the drain at the bus voltage, so the insulator is rated for the voltage and the heatsink is treated as a live part in the safety analysis. A mica pad with grease has a lower thermal resistance than a dry silicone pad, and at 11 W the difference is a few degrees.
The source leads carry the current in parallel and their inductance is part of the commutation loop. A wide pour on both sides of the board, with the leads soldered through, lowers both the resistance and the loop inductance, and the effect is visible in the drain spike.
Where the part fits and where it does not
It fits a 230 V front end at 8 to 15 A, a bridge leg in a small inverter, a boost converter on a 325 V bus, an active clamp and a flyback at 30 to 50 kHz. It does not fit a 480 V AC input, a 25 A continuous load, or a 400 V flyback without a clamp.
For a part chosen from a ladder of three die sizes the questions are the working current, the heat the enclosure allows and how the three codes compare on price. Our last time buy and LTB planning page covers how a quantity is set before a family narrows and a code disappears.
The sourcing side of this part is covered on the date code management. For a reel held between builds, that page covers how the age is tracked and when the material is set aside.
Questions we get on this code
Is it better than the 150 milliohm part? At 10 A it makes 11 W against 15 W, which is worth the extra die. At 3 A the difference is 0.4 W and the smaller part is fine.
Is 25 A available continuously? At 68.75 W, no. Ten to fifteen amps on a heatsink is the working range.
Does the tab need an insulator? Yes. The tab is the drain at the bus voltage, so a shared heatsink needs an insulator and a shoulder washer.
What should a purchase order carry? Part number, TO220, and the packing the line can take. We confirm the tube quantity on the offer.