Contact Us

VBM165R18

Brand: VBsemi
VBsemi VBM165R18 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBM165R18 — Discrete & Power Semiconductors | Superb Automation

VBM165R18

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBM165R18 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBM165R18: a 650 V, 0.34 ohm switch for a 380 V three phase bus

The VBM165R18 is a 650 V N channel MOSFET in the TO-220AB body, printed at 0.34 ohm with a 10 V gate and 11 A, 18 A of continuous drain current with the case at 25 C, 208 W of dissipation and a 367 mJ single pulse avalanche rating. The feature list leads with a reduced recovery time and recovered charge, which is the claim that matters most for a part used in a bridge.

The voltage class is chosen for the rectified bus of a 380 V three phase supply, which sits near 540 V, so 650 V leaves about 20 per cent of margin and no more. That is the standard margin for a European industrial drive and it is why a 650 V part is used rather than a 600 V one, which would be inside the bus tolerance on a high line condition.

The ratings a buyer checks first

Drain to source voltage650 V
Gate to source voltageplus or minus 30 V
On resistance at 10 V gate, 11 A0.34 ohm typical
Continuous drain current, case at 25 C and 100 C18 A and 16 A
Pulsed drain current53 A
Single pulse avalanche energy from 28.2 mH367 mJ at 5.1 A
Dissipation with the case at 25 C208 W
Linear derating factor1.7 W per C
Junction to case and junction to ambient0.5 and 62 C per watt
Gate threshold at 250 microamp2.5 V minimum, 4 V maximum
Drain leakage at 125 C, 520 V500 microamp maximum
Input capacitance at 100 V4826 pF typical
Output capacitance and reverse transfer capacitance456 and 210 pF
Effective output capacitance, energy related84 pF typical
Effective output capacitance, time related293 pF typical
Total gate charge at 520 V, 11 A71 nC typical, 106 nC maximum in the summary
Gate source and gate drain charge14 and 33 nC
Turn on delay and rise time22 and 34 ns typical
Turn off delay and fall time68 and 42 ns typical
Gate input resistance0.78 ohm typical
Body diode forward drop at 11 A0.9 V typical, 1.2 V maximum
Body diode recovery time and charge160 ns and 1.2 microcoulomb at 25 V reverse

Reading the electrical table instead of the front page

Two gate charge figures appear on the sheet for the same part. The summary prints 106 nC as a maximum and the electrical table prints 71 nC as a typical. Both can be right, and the gap matters: a driver has to supply the maximum, so 106 nC is the number that sizes the drive, while 71 nC is the number that describes an average part. A drive sized on the 71 nC figure will find the switching edge about 50 per cent slower on a worst case lot.

The capacitance rows are high for the class. An input capacitance of 4826 pF with 210 pF of reverse transfer capacitance and an internal gate resistance of 0.78 ohm is a combination that rings easily with a long gate track. The turn on delay of 22 ns and the rise time of 34 ns confirm a fast device, and a fast device with a low internal gate resistance needs the external resistor to do the damping. This is the part on this list where the gate loop geometry matters most. The drain leakage row reinforces it, since 500 microamp at 520 V and 125 C is high for a 650 V part and is another reason the die has to run cool rather than merely inside its rating.

The recovered charge needs its test condition read with it. The 1.2 microcoulomb figure is quoted at a reverse voltage of 25 V, not at the 400 V a real circuit commutates. Recovered charge rises with the reverse voltage, so the figure that applies in a 540 V bus is larger than the one printed, and the peak recovery current of 14 A is measured at the same low reverse voltage. That does not make the part a bad choice, but it does mean the diode claim on the first page cannot be taken at face value for a high voltage bridge. A measurement at the working voltage is the only honest way to use the figure, and it takes an afternoon on a double pulse bench rather than a week of simulation.

Where a 650 V part earns its place

The rectified bus of a 380 V three phase supply, power factor correction in a three phase industrial unit, an inverter stage for a small drive, welding equipment and an uninterruptible supply for a 400 V DC bus all sit in this class. In each of them the current per switch is 5 A to 15 A, the on resistance of 0.34 ohm keeps the conduction loss between 10 W and 40 W, and the 208 W dissipation rating leaves margin for a heatsink that is smaller than the switch could use.

It is also a reasonable part for a three level converter, where the switches see half the bus instead of the whole one and the 650 V rating gives almost double the margin. In that arrangement the recovered charge is more important than the on resistance, since the inner switches commutate twice per cycle, and the recovered charge figure should be measured at the working voltage before the topology is chosen. A three level arrangement also holds the inner switches on for a longer share of the cycle, so the conduction row matters more there than in a two level bridge.

Sourcing notes and the second source question

Where this part is substituted, the gate charge, the internal gate resistance and the recovered charge are the three rows that decide whether the substitute behaves the same. A candidate with a higher internal gate resistance will be quieter and slower and will change the emissions result, and one with a higher recovered charge will lose more in a bridge than it saves in conduction. Our guide to verifying a drop in replacement lists the bench measurements that catch all three before a board is released. The fourth check is thermal: a substitute with the same junction to case but a thinner die shows a different transient response, and that appears as a shorter time to thermal shutdown under a surge. Where the substitute has to be introduced on a running line, the npi production launch checklist page covers the release steps.

The commercial question for a part in this class is usually about the second source for a long life product rather than about price. An industrial customer who builds the same board for ten years needs a part with a documented life and a plan for the end of the line. The strategic sourcing page sets out how that commitment is structured, including the annual quantity review that keeps a part number in a vendor catalogue.

Questions we answer before a reel is booked

First, what gate charge the driver has to deliver. the electrical table says 71 nC typical and the summary says 106 nC maximum, and the drive has to be sized on the second. At 100 kHz that gap is a few milliamps of average gate current, which is enough to matter for a small isolated bias supply. At 100 kHz that difference is about 3.5 mA of average gate current, which is enough to matter for a small isolated supply.

Second, whether the gate loop can be kept short. With 0.78 ohm inside the package and 210 pF of reverse transfer capacitance, the part turns on in tens of nanoseconds and a 20 mm gate track will ring. The external resistor and the return path are part of the switch, not an afterthought, and the first article should show a clean gate waveform before the product is signed off.

Third, how the recovered charge was measured. The printed 1.2 microcoulomb is at 25 V reverse, and a 540 V bus will give a larger number. Where the part is used in a bridge, we ask the vendor for the recovered charge at the working voltage, and where it is not available we measure it on a first article rather than extrapolating from the low voltage row.