VBM1402
Product Specifications
VBM1402
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM1402 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM1402: 40 V and 180 A with two resistance columns far apart
The VBM1402 is a single N channel MOSFET in a TO220 body rated at 40 V drain to source, plus or minus 20 V on the gate, a 3 V threshold, 180 A of drain current, 15 milliohm at a 4.5 V gate and 2 milliohm at a 10 V gate. The die is a trench part.
The two resistance columns are the whole story of this part. Between 4.5 V and 10 V the resistance falls by a factor of more than seven, from 15 to 2 milliohm. That is not a small improvement, it is a different device, and it says the die was built for a 10 V drive with a thin gate oxide that cannot take much more than the window allows.
Forty volts is the class for a 24 V rail, a 36 V battery and a 12 V automotive rail with a clamp. It is the workhorse voltage for a 24 V motor drive, a synchronous rectifier on a 12 V output and a battery disconnect on a 36 V pack.
Key data for the VBM1402
| Configuration | Single N channel |
| Package | TO220 through hole with a metal tab |
| VDS | 40 V |
| VGS | Plus or minus 20 V |
| Vth | 3 V |
| ID | 180 A, a die figure at a 25 C case |
| RDS(on) at 4.5 V | 15 milliohm |
| RDS(on) at 10 V | 2 milliohm |
| Technology | Trench |
| Loss at 50 A | 5 W at 2 milliohm, 37.5 W at 15 milliohm |
| Loss at 100 A | 20 W at 2 milliohm |
| Drive | 10 V, since a 4.5 V drive costs seven times the conduction loss |
Nine volts of difference, seven times the loss
At 50 A the part makes 5 W when driven at 10 V and 37.5 W when driven at 4.5 V. That is the difference between a part that runs on a tab alone and one that needs a heatsink and airflow, on the same board, at the same current, with no change except the gate drive.
This is the trap in a board that reuses a 5 V gate driver from an older part. The new die is faster and lower resistance but only at 10 V, and driven at 4.5 V it behaves like a much worse part than the one it replaces. The loss budget then fails in a way that looks like a bad lot rather than a bad drive.
The 20 V gate window allows a 10 V drive with 10 V of headroom, which is enough for the ringing of a fast turn off at these currents. A 12 V rail through a driver is the normal arrangement, and a 10 V rail is close enough. What must not happen is a 15 V drive with overshoot on a die whose oxide was thinned for the low resistance column.
Forty volts on a 24 V and a 36 V system.
A 24 V lead acid pack reaches 28.8 V at the top of charge and a 36 V pack reaches 43.2 V, which is above the 40 V rating before any transient. That single number rules the part out of a 36 V lead acid system and keeps it in a 24 V one.
A 36 V lithium string at 10 cells reaches 42 V at 4.2 V per cell, which is also above 40 V. A 24 V lithium string at 7 cells reaches 29.4 V, which sits comfortably. The voltage class has to be checked against the chemistry and the cell count, not against the label on the pack.
On a 12 V automotive rail the part is comfortable in steady state and exposed during load dump, which can reach 40 V or more without a central clamp. A transient suppressor at the input is what keeps the drain inside the rating, and its clamp voltage rather than the nominal rail is the number to work to.
Two milliohm and the copper around it
At 2 milliohm the copper in the source path is a meaningful fraction of the total. A tab, a lead, a trace and a connector can add 0.3 to 0.6 milliohm, which at 100 A is several watts outside the die. A board that was laid out for a 10 milliohm part and carries this one has the same copper and a much larger share of the heat in it.
The tab of a TO220 carries the drain, and the source leaves through the leads. At 100 A the two source leads carry 50 A each, and their resistance and inductance are part of the loop. A wide copper pour on both sides of the board, with the leads soldered to both, is the way the lead resistance is halved.
At 20 W the tab needs a heatsink. At 5 W it does not, and that is where the 10 V drive earns its keep: the same part at 50 A moves from a heatsink problem to a pad problem by the drive alone.
Where the part fits and where it does not
It fits a 24 V motor drive at 40 to 60 A, a 12 V synchronous rectifier at 50 A, a 24 V battery disconnect, a power tool controller and an electronic load. It does not fit a 36 V lead acid pack, a 10 cell lithium string, or a product where the gate drive is 5 V.
For a part whose resistance depends this much on the drive, the questions are the driver rail, the copper in the source path and the clamp on a 24 V input. Our supplier scorecard page covers what is measured on the source over a quarter when a part like this carries a whole platform.
The sourcing side of this part is covered on the BOM consolidation. For a 40 V part repeated across several boards, that page covers how the codes are merged without losing a second source.
Questions we get on this code
Can it run on a 5 V gate drive? It runs, at 15 milliohm instead of 2. On a 50 A load that is 37.5 W instead of 5 W. Use 10 V wherever the loss matters.
Does 40 V cover a 36 V pack? No. A 36 V lead acid pack reaches 43.2 V and a 10 cell lithium string reaches 42 V. Both are above the rating. Use the 60 V class.
Is 180 A usable? On a large heatsink with a short loop, 60 to 80 A is realistic. At 180 A the loss is 65 W even at 2 milliohm.
What should a purchase order carry? Part number, TO220, and the packing the line can take. We confirm the tube quantity on the offer.