Contact Us

VBM1154N

Brand: VBsemi
VBsemi VBM1154N is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBM1154N — Discrete & Power Semiconductors | Superb Automation

VBM1154N

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBM1154N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBM1154N: 150 V and 50 A in a TO220 body

The VBM1154N is a single N channel MOSFET in a TO220 body rated at 150 V drain to source, plus or minus 20 V on the gate, a 3 V threshold, 50 A of drain current and 30 milliohm at a 10 V gate. The die is a trench part.

One hundred and fifty volts is the class for a 72 V battery, a 96 V string, a 110 V DC bus and a 120 V rail with transients. It is the class between the 100 V parts used on 48 V systems and the 200 V parts used on 110 V and 120 V systems, and it exists because 100 V leaves little margin on a 96 V string at the top of charge.

Thirty milliohm at 50 A is 75 W, which a TO220 with a heatsink can remove and a TO220 without one cannot. At 20 A the loss is 12 W and a small heatsink holds it. At 10 A it is 3 W and the tab alone is enough. The working current depends on the heatsink as much as on the die.

Key data for the VBM1154N

ConfigurationSingle N channel
PackageTO220 through hole with a metal tab
VDS150 V
VGSPlus or minus 20 V
Vth3 V
ID50 A, a die figure at a 25 C case
RDS(on) at 10 V30 milliohm
TechnologyTrench
Loss at 10 A3 W at 30 milliohm
Loss at 20 A12 W at 30 milliohm
Loss at 50 A75 W at 30 milliohm
Thermal pathThe tab is the drain and it is meant to be bolted to a heatsink

The TO220 tab is the reason to buy this body

A TO220 is a through hole part with a metal tab that can be screwed to a heatsink with a clip or a screw and an insulator. That gives a thermal resistance an order of magnitude better than a surface mount body of the same die area, at the cost of a hole in the board, a hand or wave solder step and a mechanical assembly.

For a 150 V part at 20 A this is the right trade. The loss of 12 W has to leave the die, and through a tab into a heatsink it does. Through a surface mount pad it does not, and the part would have to be a much larger die to compensate, which costs more than the heatsink.

The tab is the drain, so the heatsink sits at the switching potential unless an insulator is used. A mica or a silicone pad with a shoulder washer is the usual arrangement, and the thermal resistance of that pad is part of the budget. A tab at 150 V also means the heatsink has to be treated as a live part in the safety analysis.

Resistance at the working gate voltage.

The catalogue prints one column at 10 V. A 10 V drive is the normal choice on a 150 V rail because the driver sits at the source of a low side switch and the rail is there, and because the 20 V window has room for a 10 V drive with ringing.

A 3 V threshold means the part turns on from a 5 V logic output, but the resistance at 5 V is not published and is higher than the 10 V figure. Where the drive comes from a 5 V rail the loss budget has to be built on a curve rather than on the table, and the curve has to be asked for.

Gate charge at this die size is moderate, so a driver of half an amp is enough at 20 to 50 kHz. The resistor in the gate sets the transition time and the ringing, and on a 110 V rail with a fast turn off the resistor is doing real work.

One hundred and fifty volts on a 96 V string

A 96 V lead acid string reaches 110 V at the top of charge and higher during an equalisation step. A 24 cell lithium string at 4.1 V per cell reaches 98 V and 100 V at the top of a fast charge. Both sit inside 150 V with room for a clamped transient and both are above the 100 V class.

Where the product claims a 120 V DC bus, the 150 V class has 30 V of margin, which is enough for a switching spike if the loop is short and not enough if it is not. A snubber and a short loop are the difference between an 80 V spike and a 140 V one.

A 72 V battery is the comfortable case. At 84 V at the top of charge the part has 66 V of margin and the work is easy. That is where most of these parts end up, in a 72 V motor drive or a 72 V to 12 V converter.

Where the part fits and where it does not

It fits a 72 V motor drive at 15 to 25 A, a 96 V battery disconnect, a 110 V DC bus switch, a synchronous rectifier on a 48 V output and a hot swap path on a 96 V string. It does not fit a 400 V rail, a load above about 25 A without a heatsink, or a surface mount assembly with no mechanical step.

For a 96 V string the questions are the top of charge voltage, the clamp and the heatsink the enclosure can take. Our PCBA quote checklist page lists what a quote has to state so the offer and the build agree on the mechanical step.

The sourcing side of this part is covered on the incoming inspection plan. For a 150 V part bought for a long build, that page covers what is checked on each lot and what is recorded.

Questions we get on this code

Does it need a heatsink? At 20 A it makes 12 W, which a small clip on heatsink removes. At 10 A the tab alone is often enough. At 50 A it needs a real heatsink and airflow.

Is the tab isolated? No, the tab is the drain. An insulator and a shoulder washer are needed if the heatsink is earthed or shared.

Can it be driven from a 5 V output? It will turn on, because the threshold is 3 V, but the resistance at 5 V is higher than the published 10 V figure. Use a proper driver at 10 V where the loss matters.

What should a purchase order carry? Part number, TO220, and the packing the line can take. We confirm the tube or reel quantity on the offer.