Contact Us

VBM1102N

Brand: VBsemi
VBsemi VBM1102N is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBM1102N — Discrete & Power Semiconductors | Superb Automation

VBM1102N

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBM1102N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBM1102N: a 100 V N channel switch in the TO-220AB body

The VBM1102N is an N channel trench MOSFET rated 100 V drain to source with a plus or minus 20 V gate, supplied in the TO-220AB body and screened 100 per cent for gate resistance. The product summary prints 0.017 ohm at a 10 V gate with 30 A flowing, 70 A of continuous drain current with the case held at 25 C, and a junction rating of 175 C.

That 70 A figure carries a footnote instead of a thermal derivation. The sheet marks it package limited, so the silicon can pass more and the three lead body cannot. Two other rows on the same page decide what the part does inside an enclosure: 40 C per watt from junction to ambient on a one inch square board, and 3.35 W of dissipation with the ambient at 25 C. Read those two numbers first and the headline current stops being the main number in the decision.

The ratings a buyer checks first

Drain to source voltage100 V
Gate to source voltageplus or minus 20 V
On resistance at 10 V gate, 30 A, 25 C0.017 ohm typical
On resistance at 10 V gate, 30 A, 125 C0.023 ohm typical
On resistance at 10 V gate, 30 A, 175 C0.037 ohm typical
Continuous drain current, case at 25 C and 125 C70 A package limited and 35 A
Pulsed drain current145 A
Avalanche current from 0.1 mH, single pulse energy31 A and 60 mJ
Dissipation, case at 25 C and ambient at 25 C355 W and 3.35 W
Junction to case and junction to ambient0.4 and 40 C per watt
Gate threshold at 250 microamp2 V minimum, 4 V maximum
On state drain current at 10 V gate120 A minimum
Forward transconductance at 30 A25 S typical
Input, output and reverse transfer capacitance1800, 210 and 110 pF
Total gate charge at 100 V, 58 A90 nC typical
Gate source and gate drain charge23 and 34 nC
Gate resistance0.5 ohm minimum, 1.3 typical, 3.1 maximum
Turn on delay and rise time24 and 220 ns typical
Turn off delay and fall time45 and 200 ns typical
Body diode forward drop at 58 A1.0 V typical, 1.5 V maximum
Body diode reverse recovery time and charge130 ns and 0.52 microcoulomb

Reading the electrical table instead of the front page

The 0.017 ohm figure is a 30 A number. The same row repeats at 125 C and at 175 C as 0.023 and 0.037 ohm, so the part gives away roughly a third of its margin by the time the die reaches its 125 C test point and more than half of it at 175 C. A cabinet that runs the die hot therefore runs a different switch than the one the summary describes. This is the single most common reason a converter that works on a bench fails in a box with the lid on.

Run the numbers at the headline current and the package limitation becomes visible. Seventy amps through 0.023 ohm is about 113 W of conduction loss, which is 45 C of junction rise above the case at 0.4 C per watt. The case has to be near 25 C for that to work, which means a heatsink and airflow, not a bare board. With the ambient at 25 C and only 3.35 W allowed, the same part carries about 12 A before the junction reaches its limit. Both numbers are correct; they describe two different assemblies, and the quote should say which one is being discussed.

Two smaller rows are worth a look. The gate threshold tops out at 4 V, so a 4.5 V gate rail leaves almost no overdrive and no on resistance row at all is printed for that gate voltage. The avalanche rating is 60 mJ from 0.1 mH, which is enough for a small leakage spike and not enough to absorb a stalled motor, so a clamp is still cheaper than a warranty claim.

Where a 100 V TO-220 part earns its place

A 100 V part covers a 48 V rail with roughly two to one margin, which is what a telecom rectifier secondary or a 48 V DC bus in a rack wants when the load can be switched hard. It also covers a 60 V battery pack with room for a transient. It does not cover a 72 V pack at full charge, where the pack itself sits near 84 V and the switch only has a 16 per cent margin, and it does not cover a 400 V bus under any circumstances.

The second home for this class is isolated DC/DC conversion at a few hundred watts, where the 100 V rating sits on the secondary side and the 30 A to 70 A range matches a 1.5 kW to 3 kW output. The low reverse transfer capacitance of 110 pF keeps the switching edge clean at a few hundred kilohertz without a snubber, and the 90 nC of gate charge is light enough for a small driver. Where the same rating is used for motor drive at 48 V, the body diode takes the freewheel current and the 130 ns recovery is ordinary rather than fast, so the dead time has to be set with that in mind.

Sourcing notes and the second source question

A 100 V TO-220 trench switch at 0.017 ohm is a crowded field, so a second source is usually found in days rather than weeks. The mistake is to cross reference on voltage and on resistance alone. Two parts with the same 0.017 ohm at 10 V can differ by 40 per cent in gate charge and by a factor of two in output capacitance, and a driver sized for 90 nC will not always carry 130 nC at the switching frequency the supply runs at. Our power management cross reference page keeps the gate charge and the thermal rows beside the resistance for that reason.

Supply is the other half of the question. A part in a three lead tube body is a mature commodity, so the lead time tracks the general power discretes market rather than a single application. Where a programme needs a fixed date, the component lead time solutions page describes how a qualified second source is added to a live bill of materials without a full requalification cycle, and what evidence the customer keeps on file when the second part is first used.

Questions we answer before a reel is booked

The first question is the gate rail. With a threshold window that tops out at 4 V, a 10 V drive is the intended condition and the only one with a printed on resistance. A 4.5 V rail will switch the part, but nothing on the sheet tells you what the resistance becomes, and the spread between a cold and a hot part at that gate voltage is not specified at all.

The second question is the board. The steady state 40 C per watt assumes a one inch square copper pad under the drain tab, no other heat source within a few millimetres, and still air at 25 C. In a potted module, or on a board that also carries a transformer, the real figure is higher and the 12 A free air estimate falls with it. We ask for the copper area and the ambient before quoting a continuous current, because the same part is a 45 A device on one board and a 12 A device on another.

The third question is incoming inspection. The parameters that move between lots on a part of this size are the threshold and the on resistance at 10 V, so a sample plan should measure both at a controlled temperature. A TO-220AB body ships in tubes rather than on a reel, so the plan is per tube and the handling question is lead straightness rather than tape width. Our incoming inspection plan sets out a workable sample size for a tube packed power device without turning goods inwards into a laboratory.