Contact Us

VBL7401

Brand: VBsemi
VBsemi VBL7401 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBL7401 — Discrete & Power Semiconductors | Superb Automation

VBL7401

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBL7401 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBL7401: 40 V and 350 A at 1 milliohm in a seven lead body

The VBL7401 is a single N channel MOSFET in a TO263-7L body, the seven lead version of the surface mount package with a separate source lead for the gate return. Drain to source is 40 V, gate is plus or minus 20 V, threshold is 3 V, drain current is 350 A and on resistance is 1 milliohm at a 10 V gate. The die is a trench part.

The seventh lead is the point of the package. It lets the gate drive return to the source at the die rather than sharing the source lead with the load current, which removes the common source inductance that limits how fast a part with this much current can switch. On a 350 A device that inductance is the difference between a clean turn off and a drain spike that breaks the part.

One milliohm at 350 A is 122 W, so the label is not a working current. At 100 A the loss is 10 W. At 150 A it is 22.5 W. At 60 A it is 3.6 W. The current at which this part is useful is set by the copper it is soldered to and by the loop it sits in.

Key data for the VBL7401

ConfigurationSingle N channel
PackageTO263-7L, seven leads with a separate gate return
VDS40 V
VGSPlus or minus 20 V
Vth3 V
ID350 A, a die figure at a 25 C case
RDS(on) at 10 V1 milliohm
TechnologyTrench
Loss at 60 A3.6 W at 1 milliohm
Loss at 100 A10 W at 1 milliohm
Loss at 150 A22.5 W at 1 milliohm
Source connectionThe seventh lead is the gate return, use it or lose the switching speed

Why one milliohm changes the board rules

At one milliohm the package and the board are no longer a detail. A source path with 0.1 milliohm of copper is a tenth of the die resistance and at 100 A it is a watt that appears in a place with no thermal model. The same is true of the drain path and of the connector to the load. A board built for a 5 milliohm device and reworked for this one carries the same copper and twice the share of the loss outside the die.

The measurement itself is a problem. A four wire measurement at 1 milliohm with a 100 A pulse is a millivolt of signal, so lead resistance and contact resistance dominate anything done with two probes. The number in the table is a die figure at a defined gate voltage and a defined temperature, and a bench measurement that disagrees is usually measuring the fixture.

Parallel operation is where the low resistance pays. Two parts at 1 milliohm give half a milliohm, and the sharing depends on threshold matching and on how symmetrical the copper is. A board that puts one device 20 mm further from the load than the other will not share, however well the thresholds match.

Ringing, source inductance and the gate loop.

At 40 V and 150 A a fast turn off drives a large current change through the loop inductance, and the voltage across that inductance adds to the bus. The result is a drain spike that can exceed 40 V even on a 24 V rail, which is why a snubber and a short loop matter more here than on a high voltage part.

The separate gate return removes the common source inductance from the gate loop, so the gate voltage no longer moves with the load current change. What remains is the gate loop inductance itself, which sets the minimum transition time and therefore the switching loss. The gate resistor is chosen against that, and a value copied from a larger package is usually too high.

The threshold of 3 V is high for a trench part at this voltage, which is deliberate. A low threshold and 150 A of current change in the same package is an invitation to a Miller turn on. Even at 3 V, the gate has to be pulled down hard and the return has to be short.

What the body can remove

The tab on a seven lead body is the whole thermal path, and at 10 W the part is comfortable on a large copper island. At 22.5 W it needs airflow or a thick copper layer. At 40 W it needs a heatsink on the tab or a move to a different package, and 40 W is 200 A, which the label allows and the body does not.

The leads carry current as well as signal. In the seven lead body the source current goes through several leads in parallel, and their combined resistance and inductance are part of the path. A footprint that connects all of them with a wide copper pour is not a refinement, it is the difference between the die figure and the working figure.

Soldering voids under the tab matter even more at this current. A void is a hot spot, and at 100 A a hot spot grows because the resistance rises with temperature. Vacuum reflow or a profile with a long soak on the ground plane is how the void fraction is held down.

Where the part fits and where it does not

It fits a 12 V or 24 V synchronous rectifier at 50 to 100 A, a battery disconnect on a 24 V pack, a motor drive low side at 40 to 80 A, an electronic load and a hot swap path on a 24 V bus. It does not fit a 48 V rail without derating, a load above about 100 A without a copper area built for it, or a footprint that does not use the seventh lead.

For a part this close to the copper, the questions are the loop inductance, the pad area and how the parts are bought together. Our safety stock planning page covers how a buffer is sized for a part that a build cannot run without.

The sourcing side of this part is covered on the one stop BOM sourcing. For a part this close to the copper, that page covers how the surrounding passives are bought on the same order.

Questions we get on this code

Is 350 A the current I can switch? No. At 350 A the die alone makes 122 W. On a large copper island with airflow, 80 to 100 A continuous is the realistic ceiling.

Does the seventh lead have to be connected? It has to be connected to the source at the die and it has to be the gate return. Left floating or shared with the power source, the part loses the switching speed the package was made for.

Can it replace a 2 milliohm part with no board change? The footprint is the same in the six lead version, and the copper is not. At these currents the board is part of the resistance and the loop is part of the circuit.

What should a purchase order carry? Part number, the seven lead body, and the packing the line can take. We confirm the reel quantity on the offer.