VBGQTA1101
Product Specifications
VBGQTA1101
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBGQTA1101 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBGQTA1101: 100 V and 415 A with a top side cooled body
The VBGQTA1101 is a single N channel MOSFET in a TOLT-16 body, rated at 100 V drain to source, plus or minus 20 V on the gate, a 3 V threshold, 415 A of drain current and 1.2 milliohm at a 10 V gate. The TOLT is a leadless package with a metal top, and the top is where the heat leaves.
That is the difference from every other part on this page. In a normal surface mount part the heat goes down through the pad into the board, and the board has to be big enough and heavy enough to take it. In a top side cooled part the heat goes up into a heatsink that is pressed onto the package, and the board only has to carry the current.
100 V is the class for a 48 V or 72 V rail with margin, for a 60 V battery, and for the output stage of a converter that feeds a 48 V bus. At 1.2 milliohm and 415 A the part is aimed at the current path of a 3 to 10 kW converter where the board cannot remove the heat on its own.
Key data for the VBGQTA1101
| Configuration | Single N channel |
| Package | TOLT-16, leadless, metal top for cooling |
| VDS | 100 V |
| VGS | Plus or minus 20 V |
| Vth | 3 V typical |
| ID | 415 A, a die figure at a 25 C case |
| RDS(on) at 10 V | 1.2 milliohm |
| Technology | Shielded gate trench |
| Loss at 100 A | 12 W through the channel |
| Loss at 200 A | 48 W through the channel |
| Thermal path | Top metal to a heatsink, pad to the board |
| Body diode | Intrinsic, cathode at the drain |
What top side cooling asks of the assembly
A top side cooled part needs a thermal interface between the metal top and the heatsink. That interface is a pad or a paste, and it has a thickness and a resistance that the stack has to allow for. The pressure that holds it in place comes from a clip, a spring or a screw, and the pressure has to be even, or the interface is thin at one end and thick at the other.
The second requirement is coplanarity. The metal top and the board pads have to be at the same height after reflow, within a tolerance of a tenth of a millimetre, or the interface will be uneven. That is a mechanical stack up question, and it is decided before the part is chosen.
The third requirement is that the top is electrically live. It is the drain on most of these parts, so an uninsulated heatsink puts 100 V on the heatsink. The interface pad has to be insulating, and its thermal resistance is higher than a metal to metal contact.
There is a fourth requirement that is easy to miss: the top metal is also the drain and it is also a capacitance to the heatsink. A metal top pressed against a grounded heatsink adds a capacitor of a few hundred picofarads from the drain to ground, which shows up as a common mode current on every switching edge. That current either returns through the board or radiates, and on a converter at 100 kHz it is a real part of the emission budget, especially with a floating heatsink that is only tied down at one point. An insulating interface pad reduces the capacitance and reduces the coupling.
Where the heat goes at 12 and 48 W
At 100 A the part loses 12 W through the channel and the top can pass that into a modest heatsink. At 200 A it loses 48 W and the interface becomes the limit: a pad at 0.5 C per watt adds 24 C between the top and the heatsink, which is more than the junction to top resistance of the package.
The board side is not idle either. The source and drain pads carry the current and their own resistance adds heat, and the copper under the part is where that heat has to spread. A top side cooled part still needs a decent pad, just not a large one for thermal reasons.
The gain over a bottom cooled part appears above about 20 W. Below that, a normal clip package on a good board is simpler and cheaper, and the extra mechanical work of a top side interface does not pay for itself.
Where the part fits and where it does not
It fits the output stage of a 48 V to 12 V converter at 100 to 200 A, a motor drive on a 48 V or 60 V pack in a sealed enclosure, a battery disconnect on a 60 V string, and an ORing stage on a 48 V bus where the board cannot spread the heat. It does not fit a small board with no heatsink, a 96 V pack, or a product where the mechanical stack up cannot hold a tenth of a millimetre.
For a top side cooled part, the parameters that decide the build are the interface, the coplanarity and the insulation of the heatsink. Our one stop BOM sourcing page covers how a group of parts around a power stage is bought on one order with the packing the line needs.
The sourcing side of this part is covered on the component shortage forecast. For a top side cooled part with a long qualification, that page covers how a shortage is seen before it stops a line.
Questions we get on this code
Can it run without a heatsink on the top? Then it is a bottom cooled part with a poor path, and its current has to be cut to a fraction of the rating.
Does the top need an insulating pad? Yes when the heatsink is shared or grounded, because the top is the drain.
How flat does the board have to be? Within a tenth of a millimetre across the part, or the interface is uneven and the loss localises.
What should a purchase order carry? Part number, TOLT-16, and the reel quantity. We confirm the packing on the offer.