TPS622313DRYR
Product Specifications
TPS622313DRYR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS622313DRYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS622313DRYR 1.3 V at 3 MHz with the enable pull downs fitted
The TPS622313DRYR is the 1.3 V member of the TPS6223xx family in a 6 pin USON body of 1.45 mm by 1.00 mm, running at 3 MHz from a 2.05 V to 6 V input. What separates it from most of the family is the pulldown column in the device table: this member has internal pull downs on the enable and mode pins, so both are defined while the driving circuit is still unpowered or high impedance. That is a small line in a table and a large difference on a board that sequences a processor rail before the processor itself is out of reset.
The electrical core is shared with the family: 0.7 V reference, 2 per cent output accuracy, 600 milliohm typical and 850 milliohm maximum high side resistance at 3.6 V input, a switch current limit between 690 mA and 1050 mA, 25 microamp quiescent current and 0.1 microamp in shutdown. Peak output current is 500 mA, thermal shutdown is at 150 degrees junction, and the junction range is minus 40 to 125 degrees. The minimum on time of 135 ns is what limits the usable input voltage for a given output, and at 3 MHz that limit arrives sooner than on the 2 MHz members.
3 MHz is the fastest rate in the family and it exists for one reason: the inductor. A 1 microhenry part in an 0603 or 0805 body holds the ripple at 1.3 V out and 300 mA to a workable level, and the whole converter fits on the back of a module the size of a fingernail. The cost is switching loss, which at 3 MHz dominates the efficiency at light load, and the 25 microamp quiescent current is the number that decides the standby budget.
Key parameters from the SLVS941G document
| Input range | 2.05 V to 6 V, single lithium cell or two alkaline cells |
| Output | 1.3 V fixed on this member, up to 500 mA of peak current |
| Switching frequency | 3 MHz nominal on this member, the fastest rate in the family |
| Reference and accuracy | 0.7 V reference, 2 per cent output accuracy |
| High side resistance | 600 milliohm typical and 850 milliohm maximum at 3.6 V input |
| Current limit | 690 mA minimum, 850 mA typical and 1050 mA maximum |
| Quiescent current | 25 microamp with the device enabled and not switching |
| Shutdown current | 0.1 microamp typical and 1 microamp maximum |
| Enable and mode pull downs | Fitted on this member, which is the row marked yes in the device table |
| Minimum on time | 135 ns, which limits the duty cycle range at high input |
| Thermal shutdown | 150 degrees junction with hysteresis |
| Package | 6 pin USON, 1.45 mm by 1.00 mm, DRY body, marking ON |
Why an internal pull down on the enable pin matters
A converter that powers a processor core has to be off while the processor is held in reset, and it has to come up in a defined order. On a board where the enable pin is driven by a processor port, that port is high impedance until the processor is out of reset and its supply is good, which means the enable pin is floating for the first tens of milliseconds of every power up. A part with no pull down can read that floating node as high, start the core rail early, and put the processor in an undefined state.
This member removes that failure mode with a resistor inside the package. The pin is pulled low by default, the converter stays off until something drives the pin high, and the mode pin is defined the same way. On a board with several rails and a sequenced power up, that is the difference between a board that comes up the same way every time and one that depends on board cleanliness and humidity.
The trade is a small leakage in the pull down, which shows up in the shutdown current and in the current drawn from the driving port. Neither figure is significant at the microamp level, and both are inside the numbers the document quotes. The benefit is not measurable at all until a board misbehaves, at which point it is the first thing to look for.
Where this part fits
Core rails on processors and modules where the rail has to be held off until the enable is actively driven, sensor supplies, memory rails and any single cell product where the board is brought up in a fixed order. Our desk keeps the family table with the pull down column and the marking list, see power management cross reference and how to verify a drop in replacement.
What to check before a purchase order
Check the pull down column before substituting one family member for another. Most of the nineteen options have no pull down, and a board that was qualified with this part will behave differently with a sibling that relies on an external resistor that was never fitted. The substitution looks pin compatible and the rail comes up, so the fault appears only on the units that power up in the wrong sequence.
Check the inductor and the output capacitor against 3 MHz rather than 2 MHz. The same 2.2 microhenry part that works at 2 MHz has less ripple margin at 3 MHz, and the output capacitor has to hold its capacitance at the switching rate rather than just at DC. See incoming inspection plan for the goods inwards check on a 1.45 mm by 1.00 mm USON.
Questions that come up on this part
Does the internal pull down affect the current drawn from the enable driver, is the question that follows the datasheet read. It does, by a few microamps when the pin is driven high, and that is well inside what any port can source. The point of the resistor is the state when nothing is driving the pin, and that state is off.
The second question is whether 3 MHz is acceptable in an emissions test. The fundamental sits at 3 MHz with harmonics through the band, and the loop makes the rate vary with load, so the spectrum is a spread rather than a comb. A board with a radio has to keep the switch node and the inductor away from the antenna feed, and the usual 2 mm to 3 mm spacing plus a ground via fence is enough at this power level.