TPS62148RGXR
Product Specifications
TPS62148RGXR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS62148RGXR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS62148RGXR 2 A from 3 V to 17 V with two selectable switching rates
The TPS62148RGXR is the frequency selectable member of the TPS62147 and TPS62148 pair, a synchronous step down converter that takes 3 V to 17 V in and delivers 2 A from a 0.8 V to 12 V output, in a VQFN body of 2 mm by 3 mm. It uses the DCS-Control topology, holds 1 per cent output accuracy in PWM over the full junction range, and sets its carrier to 2.5 MHz when the FSEL pin is high and 1.25 MHz when it is low. That one pin is the reason this part exists: the same body and the same bill of materials serve a dense board and an efficiency first board without a second part number.
The pair splits two features. The TPS62147 carries hiccup overcurrent protection, and the TPS62148 carries active output discharge, so this member pulls the output to ground when it is disabled and lets a constant current limit hold through a fault instead of retrying. Reference voltage is 0.7 V, high side on resistance is 100 milliohm typical and 180 milliohm maximum at 4 V input, the static current limit window is 2.8 A minimum, 3.5 A typical and 4.2 A maximum, and the negative current limit is 1.5 A. Quiescent current is 18 microamp typical and 46 microamp maximum at 85 degrees junction, with 1 microamp typical in shutdown.
Load regulation is 0.05 %/A and line regulation 0.02 %/V, both quoted in PWM mode. Soft start is adjustable through the SS/TR pin, which also allows the rail to track another supply, and the power good output is open drain with a defined threshold. Thermal shutdown sits at 160 degrees junction. None of this needs external compensation, which is what makes a 2 A converter usable in a body this small without a loop calculation.
Key parameters from the SLVSDR8B document
| Input range | 3 V to 17 V, for multi cell lithium packs and 12 V intermediate rails |
| Output current | 2 A, with a static current limit from 2.8 A to 4.2 A and a 1.5 A negative limit |
| Output voltage | 0.8 V to 12 V adjustable against a 0.7 V reference |
| Switching frequency | 2.5 MHz with FSEL high, 1.25 MHz with FSEL low, adapted automatically in power save mode |
| High side resistance | 100 milliohm typical and 180 milliohm maximum at 4 V input |
| Quiescent current | 18 microamp typical and 46 microamp maximum at 85 degrees junction |
| Shutdown current | 1 microamp typical and 8 microamp maximum with the enable pin low |
| Accuracy | 1 per cent in PWM over the specified junction range, load 0.05 %/A, line 0.02 %/V |
| Output discharge | Active discharge fitted on this member, hiccup protection fitted on the TPS62147 instead |
| Soft start | Adjustable through a capacitor on SS/TR, also usable for tracking |
| Thermal shutdown | 160 degrees junction with hysteresis |
| Package | VQFN, 2 mm by 3 mm, RGX body, marking 62148 |
What the FSEL pin changes, and what it does not
Switching rate decides the size of two components. At 2.5 MHz a 2.2 microhenry inductor and two 22 microfarad ceramic capacitors hold the ripple on a 3.3 V rail; at 1.25 MHz the same ripple needs about 4.7 microhenry and a larger bank, or the same bank with more ripple. The document carries a component table for each setting, which is the sensible way to pick: start from the inductor the board can accommodate, then strap the pin to match.
The rate does not change the current limit, the reference, the accuracy or the pinout. It does change where the switching harmonics land, and that matters on a board with a radio. A 1.25 MHz carrier puts the second and third harmonics in the medium wave band, where a high impedance trace will pick them up; a 2.5 MHz carrier moves them above it. On an RF board the higher rate is usually the quieter choice, at the cost of a few points of efficiency.
In power save mode the device adapts the rate to the load regardless of the strap, so FSEL only matters in forced PWM. A board that leaves the pin floating, or that ties it through a high value resistor, will sit in an undefined state that can change with temperature. The pin is an input and wants a hard strap to either rail.
Where this part fits
Industrial controllers, connected standby products, portable instruments and any 12 V board that needs a 2 A rail with a small footprint and a defined discharge at power down. The discharge is what makes this member the one to choose when a rail has to be collapsed before another rail comes up, since the output does not wait for the load to bleed it. Our desk keeps the family comparison and the substitution notes for this pair, see power management cross reference and how to verify a drop in replacement.
What to check before a purchase order
The two members of this family are not interchangeable on features, only on pins. A board that needs hiccup on a short wants the TPS62147, and a board that needs the rail to collapse at power down wants this TPS62148. Since both regulate correctly in every normal test, the difference appears only during a fault or a sequencing check, which is exactly the test that gets skipped before a build.
Check the inductor against the 4.2 A top of the current limit rather than the 2 A rating, and check the FSEL strap against the component table for the chosen frequency, because mixing the inductor from one table with the frequency from the other gives a ripple that the output bank was not sized for. Check the output capacitor ESR against the loop at 1.25 MHz as well, since the lower rate has less margin against a high ESR bank. See incoming inspection plan for the marking and reel check on this body.
Questions that come up on this part
Can the two frequencies be changed at run time, is a question that comes up on multi mode products. They cannot: FSEL is a static strap that is read at startup, and moving it while the converter runs produces an undefined transition. A board that needs both rates should pick one and use a second converter for the other function.
The second question is whether 12 V output is realistic from a 17 V input at 2 A. The duty cycle is 71 per cent and the high side conducts for most of the period, so the 180 milliohm maximum resistance alone drops about 0.36 V at 2 A, and the inductor adds more. The part will regulate, but the input has to stay well above 13 V for the full 2 A to be available at 12 V out.