Contact Us

TPS622314DRYR

Brand: Texas Instruments
Texas Instruments TPS622314DRYR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS622314DRYR — Power Management & Signal Chain | Superb Automation

TPS622314DRYR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS622314DRYR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS622314DRYR 1.5 V at 3 MHz with 90 dB of supply rejection

The TPS622314DRYR is the 1.5 V member of the TPS6223xx family, a synchronous step down converter in a 6 pin USON body of 1.45 mm by 1.00 mm that takes 2.05 V to 6 V in and delivers up to 500 mA of peak current at a 3 MHz switching rate. The family feature list includes a supply rejection figure of up to 90 dB, which is unusual for a switching converter and is the reason this part turns up in places where a linear regulator would normally be used: a radio front end, an audio codec, a sensor analog supply.

The reference is 0.7 V with a 2 per cent output accuracy, high side resistance is 600 milliohm typical and 850 milliohm maximum at 3.6 V input, the switch current limit runs from 690 mA to 1050 mA, and quiescent current is 25 microamp with 0.1 microamp in shutdown. The minimum on time is 135 ns, thermal shutdown is at 150 degrees junction, and the junction range is minus 40 to 125 degrees. Nineteen fixed output voltages share this document and this body, from 1.0 V to 3.3 V, and the 1.5 V option carries the marking OT.

Ninety decibels of rejection is a claim about a specific condition: the input ripple at a given frequency against the output ripple at the same frequency, measured with the recommended input capacitor. It is not a guarantee across the band. What it does mean is that the converter can sit behind a noisy 3.6 V rail and still deliver a quiet 1.5 V, provided the input capacitor is close enough and the ground return is clean. That is a different proposition from a linear regulator, which rejects the same ripple regardless of the board.

Key parameters from the SLVS941G document

Input range2.05 V to 6 V, single cell lithium or two alkaline cells
Output1.5 V fixed on this member, up to 500 mA of peak output current
Switching frequency3 MHz nominal, with the hysteretic loop varying the rate with load
Supply rejectionUp to 90 dB, measured with the recommended input capacitor at the stated condition
Reference and accuracy0.7 V reference, 2 per cent output accuracy
High side resistance600 milliohm typical and 850 milliohm maximum at 3.6 V input
Current limit690 mA minimum, 850 mA typical and 1050 mA maximum
Quiescent current25 microamp enabled and not switching, 0.1 microamp in shutdown
Minimum on time135 ns, so a 1.5 V output needs at least about 2.6 V of input at 3 MHz
Family optionsNineteen fixed voltages from 1.0 V to 3.3 V in the same body
Thermal shutdown150 degrees junction with hysteresis
Package6 pin USON, 1.45 mm by 1.00 mm, DRY body, marking OT

Where a switching converter can stand in for a linear one

A linear regulator rejects input ripple down to DC, and a switching converter rejects it only above the loop bandwidth. Below a few kilohertz the switch mode part passes the input variation through, because the loop simply adjusts the duty cycle to keep the output constant while the input moves. The 90 dB figure belongs to the switching frequency and its harmonics, where the input capacitor and the inductor form the filter and the ripple attenuation is large.

That distinction decides where this part can be used. A rail that has to reject a 1 kHz supply wobble needs a linear stage after it, or a much larger input capacitor. A rail that has to reject the 3 MHz ripple of an upstream converter needs exactly this device, because the attenuation at that frequency is enormous and the loss is far below what a linear regulator would dissipate.

The 2 per cent accuracy is the other half of the trade. A linear regulator with a 1 per cent reference beats this part on DC accuracy, and this part beats it on efficiency by a wide margin at 300 mA. For a 1.5 V rail from a 3.6 V cell the difference is 2.1 V of drop through a pass element against a switching stage that loses a few per cent.

Where this part fits

Sensor analog supplies, audio codec rails, radio baseband rails and any single cell product where a 1.5 V rail has to be quiet at the switching frequency and efficient at 300 mA. Our desk keeps the family table with the nineteen voltage options and their markings, see power management cross reference and pin to pin cross reference.

What to check before a purchase order

Check the marking against the voltage table. 1.5 V is OT, 1.3 V is ON, 1.1 V is QF and 1.8 V is OQ, and all four sit in the same body with the same pinout. A reel that is verified by label rather than by marking will eventually put a 1.3 V part on a 1.5 V rail, and the resulting board will pass every functional test except the one that measures the rail.

Check the input capacitor against the 90 dB claim, since that number is quoted with a specific input capacitor in a specific position. A 4.7 microfarad part 10 mm away from the pin turns the rejection into something much smaller, and the board will show switching ripple on the output that the datasheet curve says should not be there. See incoming inspection plan for the receipt checks on this body.

Questions that come up on this part

Can the part replace an LDO directly, is the question that opens most conversations about it. It can replace an LDO that is dropping from a cell to 1.5 V at a few hundred milliamps, and it cannot replace one that has to reject a slow input variation or hold 0.5 per cent DC accuracy. The output capacitor and the inductor are the two components that have to be added, and they are what the board area comparison comes down to.

The second question is whether the 500 mA peak rating means 500 mA continuous. The switch current limit is quoted at 850 mA typical, which supports a 500 mA output at moderate duty cycle, and the thermal path in a 1.45 mm by 1.00 mm body is the real limit at high ambient. A board that draws 500 mA continuously at 85 degrees ambient should measure the case temperature rather than trust the headline.