Contact Us

TPS62221DDCR

Brand: Texas Instruments
Texas Instruments TPS62221DDCR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS62221DDCR — Power Management & Signal Chain | Superb Automation

TPS62221DDCR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS62221DDCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS62221DDCR 400 mA at 1.25 MHz fixed at 1.5 V in a thin SOT-23

The TPS62221DDCR is the 1.5 V member of the TPS6222x family, a synchronous step down converter that delivers up to 400 mA from a 6 pin SOT-23-THIN body of 1.6 mm by 2.9 mm. The input range starts at 2.5 V and stops at 6 V, which makes it a single lithium cell or three cell nickel part rather than a 12 V converter, and the switching rate is a fixed 1.25 MHz with power save operation at light load. Nine fixed output voltages sit in the same document, from 1.2 V to 2.3 V, plus an adjustable member.

The quiescent current is 15 microamp typical and 25 microamp maximum with the enable pin at ground, and the shutdown current is 0.1 microamp typical and 1 microamp maximum. The P-channel current limit is 600 mA minimum, 670 mA typical and 880 mA maximum, the undervoltage lockout sits between 1.5 V and 2 V, and the absolute maximum on the supply pin is 7 V. The output is rated at 400 mA continuous, which leaves the limit window comfortably above the load and well below what a small inductor can saturate at.

The part is small in every sense. A 1.5 V rail at 400 mA is the kind of supply a baseband processor, a memory device or a sensor hub asks for, and the whole converter fits on the opposite side of the board from the load with two ceramic capacitors and one inductor. There is no compensation pin, no soft start capacitor and no feedback divider on the fixed members, so the bill is four components and the board question is which ground to return the output capacitor to.

Key parameters from the TPS6222x document

Input range2.5 V to 6 V, with the absolute maximum on the supply pin at 7 V
Output1.5 V fixed on this member, 400 mA rated
Switching frequency1.25 MHz typical, from 0.8 MHz to 1.85 MHz across the spread
Current limitP-channel limit 600 mA minimum, 670 mA typical and 880 mA maximum
Quiescent current15 microamp typical and 25 microamp maximum with the enable pin at ground
Shutdown current0.1 microamp typical and 1 microamp maximum
Undervoltage lockoutBetween 1.5 V and 2 V, so a single cell at end of discharge is outside the window
Output options1.2 V, 1.5 V, 1.6 V, 1.7 V, 1.8 V, 1.875 V, 2.2 V and 2.3 V fixed, plus an adjustable member
Package6 pin SOT-23-THIN, 1.6 mm by 2.9 mm, DDC body, 3000 pieces on a large reel
TemperatureMinus 40 to 85 degrees ambient for the whole family
Feedback dividerNot present on the fixed members, external on the adjustable one with a 1 megohm total limit

Light load behaviour on a 400 mA converter

Below a few tens of milliamps this part leaves continuous conduction and enters power save mode, where the switching rate falls with the load and the quiescent current drops to 15 microamp. The output ripple becomes a burst pattern rather than a fixed frequency waveform, and the efficiency at 1 mA is far above what a forced PWM part achieves. For a battery powered board that spends most of its life asleep, that is the whole point of the device.

The cost is a variable carrier. A burst pattern has a repetition rate in the audible range, and a ceramic output capacitor with a high dielectric constant can sing at that rate under a light load. On a handset that is a faint buzz in a quiet room; on an instrument it is a complaint. The family has no way to force PWM at light load, so a board that cannot accept the burst behaviour has to keep the load above the skip threshold with a bleed resistor, which costs more standby current than the mode saves.

The 1.25 MHz carrier also sets the inductor. A 2.2 microhenry part holds the ripple on a 1.5 V rail at 400 mA to about 200 mA peak to peak, which is half the load; a 4.7 microhenry part halves that. In a body this small the taller inductor is usually the limiting dimension, so most boards stay at 2.2 microhenry and accept the ripple, which the ceramic output capacitor absorbs without trouble.

Where this part fits

Single cell lithium and three cell nickel products, sensor hubs, memory rails, baseband cores at 1.5 V and any board that needs a 400 mA point of load supply in a 1.6 mm by 2.9 mm body. Our desk keeps the cross reference and the substitution notes across the nine fixed voltage options, see power management cross reference and pin to pin cross reference.

What to check before a purchase order

The output voltage is carried in the order code and in the package marking, and the markings are not mnemonic: 1.5 V is ALO, 1.6 V is ALQ, 1.2 V is BRZ. A reel that arrives with a marking nobody checks will produce a board that comes up at the wrong rail, and because the family shares one document and one body the fault looks like a board error rather than a purchase error. The DDC suffix with an R is 3000 pieces on a large reel and with a T is 250 on a small one.

Check the load against the 400 mA rating at the top of the ambient range. The part is specified to 85 degrees ambient, and at 400 mA from 3.6 V to 1.5 V the dissipation is small but the body is a SOT-23 with no thermal pad, so the copper around the pins is the only heat path. Check the input capacitor against the 7 V absolute maximum as well, since a 5 V rail with a hot plug transient can exceed it. See incoming inspection plan for the marking check we run on this family.

Questions that come up on this part

Can the adjustable member be used to make 1.5 V instead of stocking the fixed one, is a common question. It can, with two resistors, but the divider draws current from the output at all times and the fixed part is the cheaper and smaller answer. On a 15 microamp standby budget the divider alone can cost more than the converter saves.

The second question is whether the part can start from a single cell at 2.7 V. It can, because the input range starts at 2.5 V, but the 1.5 V output at 400 mA needs the cell to hold up, and the internal resistance of a small cell at end of discharge will pull the input below the lockout under a load step. A 10 microfarad input capacitor close to the pin is the usual mitigation.