AD7732BRUZ
Product Specifications
AD7732BRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD7732BRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD7732BRUZ: Two Differential Channels at 16 Noise-Free Bits and 2 kHz Switching
The AD7732 is a 24-bit sigma-delta front end built around the problem of switching between channels quickly. Two fully differential inputs accept plus or minus 5 V, plus or minus 10 V, 0 V to 5 V or 0 V to 10 V, and the overvoltage tolerance is the feature that separates it from a general purpose converter: an input can be driven to plus or minus 16.5 V without disturbing the channel being converted, and the absolute maximum on the pin is plus or minus 50 V. On a process control card where a field wire can be connected to the wrong terminal, that is the difference between a measurement that continues on the healthy channel and a board that has to be replaced.
Resolution is quoted per output rate, not per part
The converter is 24 bits with no missing codes and 0.0015 percent nonlinearity, but the number that decides a channel switching system is the noise-free resolution at the rate the system actually runs. At 500 Hz the part delivers 18 bits peak to peak, which the vendor also states as 21 bits effective. At 2 kHz it is 16 bits peak to peak and 19 bits effective, and at 15 kHz it is 14 bits peak to peak and 18 bits effective. The peak to peak figure is the one to use for a control decision, because it describes the band inside which the reading moves with a steady input, while the effective bits figure is an rms statement that sounds better by about three bits. Reading the two as interchangeable is how a 21-bit claim ends up in a specification for a loop that only needs 2 kHz.
Conversion time and the switching overhead
True 16-bit peak to peak resolution is achievable with a total conversion time of 500 microseconds, which is the 2 kHz channel switching rate, and the part can be pushed to 15.4 kHz when the resolution requirement drops. Channel switching is what the architecture is arranged around: each channel has its own calibration registers, so the offset and gain corrections for channel 0 do not have to be reloaded when the multiplexer moves to channel 1. In a two channel system alternating at 2 kHz, that halves the settling burden, because a channel that was calibrated in production keeps its correction across the switch.
| Parameter | Value | What it decides |
|---|---|---|
| Resolution | 24 bits, no missing codes | No gaps in the code set at any rate |
| Nonlinearity | 0.0015 percent | About 393 codes at 24 bits, not the limiting term |
| Channels | Two fully differential | One part per pair of field inputs |
| Input ranges | Plus or minus 5 V, plus or minus 10 V, 0 to 5 V, 0 to 10 V | Wide industrial signals without a scaling stage |
| Overvoltage | Plus or minus 16.5 V without affecting the other channel | A miswired field input does not corrupt the reading |
| Absolute maximum | Plus or minus 50 V on an input | Survives a fault, not just a tolerance |
| Noise free resolution | 18 bits at 500 Hz, 16 bits at 2 kHz, 14 bits at 15 kHz | The number to quote against a control loop requirement |
| Conversion time | 500 microseconds for 16 bits peak to peak | 2 kHz channel switching |
| Supply | 5 V analogue, 3 V or 5 V digital | 3.3 V logic without level shifters |
| Temperature | Minus 40 C to plus 105 C | Extended industrial, not just commercial |
| Package | 28-lead TSSOP | Two channels in a narrow body |
Calibration and the missing reference
Per channel system calibration means the part can measure its own offset and gain against the external reference and store the correction for each channel separately, which is what makes a two channel card maintainable without a trim step at final test. The differential reference input also carries a no reference detect function, so firmware can distinguish a live reference from a missing or unpowered one instead of reading a plausible number that happens to be wrong. The serial port is three wire and compatible with SPI, QSPI, MICROWIRE and DSP hosts, with Schmitt triggers on the logic inputs, which keeps the port usable when the cable to the host is long or the edge rates are slow.
Where it fits
Programmable logic controllers and distributed control systems, multiplexed industrial instrumentation and process control are the natural applications, because all of them alternate between a small number of wide range signals and all of them care more about noise-free bits at their own rate than about a headline number. The sibling parts are useful selection references: the AD7734 has four single-ended inputs with true bipolar ranges to plus or minus 10 V, and the AD7738 has eight single-ended or four differential channels with smaller ranges for lower level signals. For converter comparisons across ADI families, the ADC and DAC cross reference page sets out the pairs, the ADI part second source page covers alternatives, and the strategic sourcing page covers multi year supply arrangements on parts of this class.