Contact Us

TPS65154RSLR

Brand: Texas Instruments
Texas Instruments TPS65154RSLR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS65154RSLR — Power Management & Signal Chain | Superb Automation

TPS65154RSLR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS65154RSLR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS65154RSLR liquid crystal bias supply with a six channel white LED driver

The TPS65154RSLR is a complete bias block for a notebook or tablet panel. It holds two boost converters, one linear regulator, a programmable common voltage buffer with on chip EEPROM, a gate voltage shaping block, a panel reset signal and a six channel white LED driver, all in a 48 pin VQFN of 6 mm by 6 mm on a 0.4 mm pitch. The input range is 2.0 V to 5.5 V, which covers a 3.3 V rail and a single cell battery node, and the electrical tables are specified over a minus 40 to 85 degree ambient range.

The two converters split the panel rails. The first is a synchronous boost that produces the source driver voltage, quoted from 6.5 V to 9.6 V and able to deliver 400 mA from a 3.7 V input. The second is a non synchronous boost for the gate high rail, which reaches a higher voltage at a much lower current and needs an external diode and capacitor. The linear regulator produces the logic rail between 1.0 V and 2.5 V directly from the input, and the common voltage buffer is calibrated through the EEPROM so the panel setting is held without host software intervention on every power up.

The six channel driver is the part that decides the backlight behaviour. It supports direct dimming and phase shifted dimming, so the six strings can be staggered in time to spread the current pulses and reduce the load on the input capacitor and on the battery.

Key parameters from the SLVSBG2A document

Input range2.0 V to 5.5 V normal operation, 7 V absolute maximum on the supply pins
Source railSynchronous boost, 6.5 V to 9.6 V, 400 mA at VIN 3.7 V
Gate railNon synchronous boost with external diode, voltage shaping for the gate driver
Logic railLinear regulator from 1.0 V to 2.5 V, supplied directly from VIN
Common voltageProgrammable calibrator with buffer, settings held in the on chip EEPROM with a write protect pin
BacklightSix channel white LED driver, direct dimming and phase shift dimming modes
SequencingPanel reset output XAO, timing controller reset output RST, both with programmable delay
InterfaceI2C for settings and EEPROM access
ProtectionThermal shutdown, undervoltage lockout on the input, active discharge on power down
PackageRSL 48 pin VQFN of 6 mm by 6 mm, 0.4 mm pitch, moisture level 3 with a 168 hour floor life

Why the EEPROM changes the production flow

The common voltage is a per panel setting. On a part without EEPROM the host has to write that value at every start, which means a bus transaction on the critical path of the power up sequence and a software dependency that follows the panel supplier. With the EEPROM inside the bias block the value is programmed once on the line, protected by the write protect pin, and read back on every start without the host.

The same applies to the timing of the panel reset and the source rail ramp. Those values are written into the part rather than into the application processor, so a panel change becomes a programming step on the line rather than a software release. That is the practical reason this class of part sits in front of the panel connector instead of being folded into a general purpose PMIC.

Where this part fits

Notebook and tablet panels, and any product that needs a source rail, a gate rail, a logic rail, a calibrated common voltage and a six string backlight from one 3.3 V supply. Our desk tracks this class of part under power management cross reference and obsolete part cross reference hub.

What to check before a purchase order

Check the moisture level. This body is published at level 3 with a 168 hour floor life, which means a reel that has been open for a week needs a bake before reflow unless the line keeps a dry cabinet. A plant without a bake oven has to plan the reels accordingly, and the 2500 piece reel size sets how long a reel actually stays on the line.

Check the gate rail against the panel specification rather than against the part rating. The gate high voltage and the shaping profile come from the panel data, and a bias block programmed for one panel family will not drive another even though the pinout is identical. The incoming check for programmable parts is in incoming inspection plan.

Questions that come up on this part

Can the six channels drive fewer strings? Yes, unused channels are left open and the driver regulates the remaining ones, which is how a 4 string panel uses the same part.

What happens when the input falls below the lockout? The converters stop, the logic rail follows the input down, and the panel reset output goes low, which is the sequence a panel needs to avoid a latched state.