TPS630250RNCR
Product Specifications
TPS630250RNCR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS630250RNCR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS630250RNCR single inductor buck boost at 2 A
The TPS630250RNCR is a four switch buck boost converter that takes 2.3 V to 5.5 V in and delivers up to 2 A at an adjustable output, using one inductor and no mode selection pin. It transitions between buck and boost automatically as the input crosses the output, so a rail holds 3.3 V while a lithium cell falls from 4.2 V to 2.5 V and then continues to hold as the cell falls below the output. The body is the RNC VQFN of 14 pins, and the family also offers the same converter in a 20 pin DSBGA.
The switching frequency is 2.5 MHz typical, the quiescent current is 35 microamp, and the efficiency reaches 95 per cent in buck or boost and about 97 per cent when the input equals the output. The adjustable member sets its output with a divider on the FB pin, and the fixed members of the same document carry a preset level so that a board with a standard rail needs no divider. The maximum average current in the switches is 4.5 A typical, which is what supports 2 A at the output in boost mode.
The four switch topology is what makes the seamless transition possible. In buck mode the two left switches chop and the two right switches rectify; in boost mode the roles swap; in the transition region the part runs a mixed sequence so that the output does not glitch as the input passes through it. A two stage buck then boost arrangement cannot do that without a dead band, and a dead band at 3.3 V is where a single cell product spends most of its life.
Key parameters from the SLVSBJ9B document
| Input range | 2.3 V to 5.5 V |
| Output | Adjustable on this member through the FB pin, preset on the fixed members of the family |
| Output current | 2 A continuous, with 4.5 A typical average switch current |
| Switching frequency | 2.5 MHz typical, fixed frequency PWM with synchronous rectification |
| Quiescent current | 35 microamp typical |
| Efficiency | Up to 95 per cent in buck or boost, about 97 per cent when the input equals the output |
| Topology | Four switch single inductor, automatic buck to boost transition |
| Feedback | External divider on the adjustable member, connected to the output on the fixed members |
| Inductor | 1 microhenry in the application circuit of the document |
| Capacitors | 10 microfarad input and two 22 microfarad output capacitors in the application circuit |
| Packages | RNC VQFN of 14 pins and YFF DSBGA of 20 pins |
| Shutdown | Enable pin with a defined shutdown state and no output discharge path on this member |
Why a buck boost and not two converters
A 3.3 V rail on a single cell lithium battery spends its life on both sides of the output voltage. Above 3.3 V the converter bucks, below it boosts, and around it the two modes meet. Two separate converters would need a mode switch at exactly the point where the battery voltage crosses the rail, which is where a product operates for most of its discharge. The four switch topology removes the switch and the dead band that goes with it.
The cost is a higher part count inside the package and a ripple that is larger than a pure buck, because the inductor current is continuous and never reaches zero in boost mode. On a rail that feeds a radio the ripple spectrum at 2.5 MHz is easy to filter, which is why the converter is common in handheld products. On a rail that feeds a precision reference the same ripple needs a second stage.
The 2 A rating is a switch current statement. In boost mode the input current is higher than the output current, so at 2 A out and 2.5 V in the input side carries about 3 A, and the 4.5 A average switch limit is what allows it. At the bottom of the input range the usable output current is smaller than at the top, and a customer who needs the full 2 A near 2.5 V should check the curves rather than the headline.
Where this part fits
Single cell lithium products that need a 3.3 V rail across the whole discharge, handheld instruments, portable medical monitors, wireless terminals and any board where the input crosses the output during normal operation. The cross reference notes are at power management cross reference and the drop in check is at how to verify a drop in replacement.
What to check before a purchase order
Check whether the board needs the adjustable member or a fixed one. The adjustable part carries a divider and the fixed parts do not, and the two are the same body with the same pin count, so a reel picked by body alone can deliver a part whose FB pin expects to be tied to the output. The result is a rail at the internal reference rather than at the intended level.
Check the inductor saturation current against the 4.5 A switch limit, not against the 2 A output rating, because in boost mode the inductor carries more than the output. A 2 A inductor will work in buck and saturate in boost, and the failure appears only when the battery is low, which is exactly when the product is about to be charged.
Questions that come up on this part
Can the output be higher than the input on this part, is a common question, and it can, which is the whole point of the topology. A 5 V output from a 3.7 V cell is inside the range. The limit is the switch current: at 5 V out the output current available from a 3 V input is smaller than at 3.3 V out, and the curves in the document are the place to read it.
The second question is whether the converter can be disabled without draining the battery. It can, through the enable pin, and the shutdown current is specified in the electrical table rather than assumed. A board that leaves the enable floating will not be in a defined state, so the enable has to be tied to a supervisor or to a pull down.