Contact Us

TPS65023BRSBR

Brand: Texas Instruments
Texas Instruments TPS65023BRSBR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS65023BRSBR — Power Management & Signal Chain | Superb Automation

TPS65023BRSBR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS65023BRSBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS65023BRSBR three converter PMIC with three LDOs

The TPS65023BRSBR is a power management IC for processor based products: three synchronous step down converters, two general purpose 200 mA LDOs, a 30 mA real time clock LDO with a switch, an I2C interface and dynamic voltage scaling on the core rail. The converters deliver 1.7 A on the core rail, 1.2 A on the system rail and 1.0 A on the memory rail, and the vendor quotes efficiencies of 90, 95 and 92 per cent respectively. The body is a 40 pin WQFN of 5 mm by 5 mm and the rated ambient range is minus 40 to 85 degrees.

The B suffix is the part with the faster I2C timing: setup and hold time is 100 ns on the TPS65023B against 300 ns on the plain TPS65023. Both parts run the bus at up to 400 kHz in fast mode, so the B is the one to specify when the host drives a short bus at the top of the fast mode window and the margin on the older part is thin.

Two digital input pins, DEFLDO1 and DEFLDO2, choose among four preset LDO output combinations at power up, so a board can be built for several product variants without a bus write. The reset delay is set by an external capacitor, and a battery backup function keeps the real time clock alive when the main cell is removed. Quiescent current for the whole device is 85 microamps.

Key parameters from the SLVS670L document

Converter 11.7 A, 90 per cent efficient, core rail, 0.6 V to the input voltage
Converter 21.2 A, up to 95 per cent efficient, system rail
Converter 31.0 A, 92 per cent efficient, memory rail
Linear regulatorsTwo 200 mA LDOs from 1.5 V to 6.5 V input, plus a 30 mA RTC LDO with a switch
Converter input2.5 V to 6 V on VINDCDC1, tied with VINDCDC2, VINDCDC3 and VCC
InterfaceI2C fast and standard mode up to 400 kHz, 100 ns setup and hold on the B part
Voltage scalingDynamic voltage management on the core converter through the serial interface
LDO presetsFour combinations selected by the DEFLDO1 and DEFLDO2 pins at power up
Quiescent current85 microamps for the device, low ripple PFM mode at light load
PackageRSB 40 pin WQFN of 5 mm by 5 mm, NIPDAU finish, minus 40 to 85 degrees

Sequencing and the real time clock

Each converter has its own enable pin, and the LDO group has an input pin of its own, so the power up order is set by the host or by a simple RC chain rather than by an internal state machine. That is flexible and it is also the part of the circuit that goes wrong most often: a rail that comes up before its reference is valid pulls current through a substrate diode, and the symptom is a warm part on a board that otherwise works.

The RTC branch is separate for a reason. It runs from a backup cell, draws microamps, and keeps the clock domain alive while the rest of the board is off. A product that loses time on a battery swap has usually lost the backup cell, not the PMIC.

Where this part fits

Portable media players, internet audio players, cameras, smart phones and processor boards that need a core rail, an input output rail, a memory rail and two quiet analogue rails from one 3.6 V cell. The substitution notes for this class of part sit under power management cross reference.

What to check before a purchase order

Check the reel letter. The vendor addendum lists the B family rows with TPS65023BRSBT at 3000 pieces on a large reel, and the tape and reel table prints TPS65023BRSBR at 250 pieces on a 330 mm reel, which is the opposite of the usual convention where R is the large reel. A production call off written from the letter alone can land on a 250 piece reel, so the quantity column has to be read on the same row as the code.

Check the B against the plain part as well. Both are active, both are the same body, and the difference is the bus timing, which does not show up on a bench that runs the bus at 100 kHz. The receipt check for a mixed reel is in date code management.

Questions that come up on this part

Can the converters be paralleled? No. Each has its own feedback pin and its own compensation, and there is no sharing mechanism.

What happens when the input falls below 2.5 V? The converters stop and the LDOs continue until their own dropout is reached, so the RTC branch and the 1.5 V capable LDOs can still run from a nearly empty cell while the core rail is gone.