Contact Us

TPS65270RGER

Brand: Texas Instruments
Texas Instruments TPS65270RGER is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS65270RGER — Power Management & Signal Chain | Superb Automation

TPS65270RGER

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS65270RGER from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS65270RGER dual synchronous buck from 4.5 V to 18 V

The TPS65270RGER is a two channel synchronous buck regulator with integrated switches, a 4.5 V to 18 V input and a maximum continuous output current of 2 A on the first converter and 3 A on the second. The output voltage is set by an external divider against a 0.8 V reference quoted at 1 per cent, and the vendor lists output voltages up to 15 V. The body is a 24 pin VQFN of 4 mm by 4 mm rated minus 40 to 85 degrees ambient, and the same silicon is also published in a 24 pin HTSSOP.

The two channels switch 180 degrees apart, which spreads the input current pulses and lets a smaller ceramic bank carry the same ripple. Each channel has its own enable pin and its own soft start pin, so the two rails can be brought up in either order and at different rates. The converter starts into a pre biased output without a discharge pulse, and the oscillator is set by a resistor from 300 kHz to 1.4 MHz.

At light load the part enters a pulse skipping mode, which is what keeps a standby rail efficient in a product that spends most of its life waiting. The transition back into continuous conduction is automatic and does not need a mode pin.

Key parameters from the SLVSAX7E document

Input range4.5 V to 18 V, suitable for 5 V, 9 V, 12 V and 15 V buses
Output range0.8 V to 15 V, external divider per channel
Reference0.8 V with 1 per cent accuracy
Output currentUp to 2 A on converter 1 and 3 A on converter 2, continuous
Switching frequency300 kHz to 1.4 MHz set by an external resistor
Phase relationship180 degrees between the two channels
Soft startDedicated pin per channel with an internal charging current
Start-upStarts into a pre biased output without discharging it
Light loadPulse skipping mode for efficiency at low output current
PackageRGE 24 pin VQFN of 4 mm by 4 mm, 3000 pieces on a large reel, moisture level 1

Two bodies, one electrical part

The vendor publishes this part in a VQFN and in an HTSSOP. The electrical behaviour is the same, the pinout is not, and the thermal resistance is different enough to change what the part can deliver in a hot enclosure. The VQFN carries the lower thermal resistance and the smaller footprint, which is why most new boards take it; the HTSSOP remains in production for boards that were released on it and for plants whose reflow profile was written around a leaded package.

The moisture levels differ as well, level 1 for the VQFN body against level 2 for the HTSSOP row, so a line that mixes both on one panel has two floor life rules to track.

Where this part fits

Set top boxes, routers, home gateways, automotive aftermarket units and any board that needs a 3.3 V and a 1.8 V rail from a 12 V bus with a controlled order. Cross reference notes sit under power management cross reference and one stop BOM sourcing.

What to check before a purchase order

Check the body letter. RGE is the VQFN and PWP is the HTSSOP, and the two do not share a land pattern. A purchase order that names the family and the reel size but not the body can deliver a part that does not fit the board, and the mistake is only visible at the placement machine.

Check the current split between the channels. This part is asymmetric, 2 A on one channel and 3 A on the other, so a rail that was budgeted at 3 A on both will be short on the first channel. The reel and date check is in date code management.

Questions that come up on this part

Can the two channels be paralleled for 5 A? No, there is no current share mechanism, and two loops with independent references will split the current unevenly.

What sets the minimum output voltage? The 0.8 V reference, so a 0.6 V core rail needs a different part rather than a different divider.

One more point on the current split. The two channels are not equal, 2 A on the first and 3 A on the second, and the phase relationship is fixed rather than selectable, so a board that needs the larger rail on the first channel has to swap the assignments rather than the parts. The soft start pins also sit on separate capacitors, which means the slower ramp can be put on whichever rail is loaded by the larger output capacitance without affecting the other.

The two soft start capacitors can be sized independently, so a rail with a large output bank is brought up more slowly than the other without changing the order in which the enables are released.