VBE17R08S
Product Specifications
VBE17R08S
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBE17R08S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBE17R08S: a 700 V super junction switch at 0.56 ohm
The VBE17R08S is an N channel super junction MOSFET in the TO-252 outline, printed at 700 V from drain to source and plus or minus 30 V on the gate. On resistance is 0.560 ohm typical at a 10 V gate with 6 A flowing, continuous drain current is 8 A with the case at 25 C and 5 A with the case at 100 C, and the pulsed rating is 24 A. The single pulse avalanche energy is 330 mJ from a 100 V rail into 30 mH at 4 A, and the junction to case figure is 0.85 C per watt, the same thermal body as the 650 V member of the family.
The 700 V rating is the reason to choose this part over its 650 V sibling. On a 400 V bus with a 15 per cent overshoot, a 650 V device leaves 6 V of margin while a 700 V device leaves 56 V, and the difference shows up in field returns rather than on the bench. The premium is paid in resistance, 0.560 ohm against 0.240 ohm, and in current, 8 A against 15 A, so a buyer gains voltage margin by giving up roughly half the current capability in the same outline.
The ratings a buyer checks first
| Drain to source voltage | 700 V |
| Gate to source voltage | plus or minus 30 V |
| On resistance at 10 V gate, 6 A, 25 C | 0.560 ohm typical |
| Continuous drain current, case at 25 C | 8 A |
| Continuous drain current, case at 100 C | 5 A |
| Pulsed drain current | 24 A |
| Single pulse avalanche energy | 330 mJ from 100 V into 30 mH, 4 A peak |
| Power dissipation, case at 25 C | 180 W, 1.7 W per C derating |
| Junction to case, junction to ambient | 0.85 and 62 C per watt |
| Gate threshold voltage | 2.0 V minimum, 4.0 V maximum |
| Total gate charge at 10 V gate and 480 V drain | 25 nC typical |
| Input, output and reverse transfer capacitance | 2300, 51 and 12 pF |
| Turn on delay and rise time | 12 and 14 ns typical |
| Turn off delay and fall time | 61 and 16 ns typical |
| Body diode forward voltage at 5 A | 1.2 V maximum |
| Reverse recovery time and charge | 55 ns and 6.4 microcoulomb typical |
| Junction and storage range | minus 55 to plus 150 C |
Reading the electrical table instead of the front page
Eight amps through 0.560 ohm is 36 W, so the 8 A rating is a case temperature rating rather than an operating point. In still air the junction to ambient path of 62 C per watt allows about 1.4 W from a 60 C ambient to a 150 C junction, which is 1.6 A of continuous current. On a well padded board the practical figure rises towards 3 A. Everything above that belongs to a pulse or to a heatsink, and a buyer who reads the front page as a continuous rating will end up with a hot tab and a short life.
The capacitance row is the one that differs from the 650 V member even though the gate charge is identical. Input capacitance is 2300 pF against 1900 pF, while the gate charge is 25 nC on both and the switching times match to the nanosecond. That pattern says the two parts share a gate structure and a driver requirement but not a drift region: the 700 V die needs more area for the same charge, and the extra area shows up as input capacitance. A driver that worked on the 650 V part still works here, but the turn off dV/dt and the ringing frequency of the gate loop will move.
The diode is slower than on the 650 V member, at 55 ns typical and 110 ns maximum of reverse recovery with 6.4 microcoulomb typical and 12.8 maximum of recovered charge, quoted at 5 A and 100 A per microsecond. The gate resistance is 0.7 ohm typical and 1.4 ohm maximum, and the threshold window of 2.0 V to 4.0 V is wide enough that a 3.3 V logic drive is not a defined condition. For a 700 V part this is ordinary; the row still has to be read, because a board that switches at 200 kHz will notice 12.8 microcoulomb.
The avalanche rating of 330 mJ is the strongest row on the sheet relative to the current class. A 8 A part that absorbs 330 mJ without damage can clamp a transformer leakage event that would destroy a part rated at a tenth of that, and it is the reason this device survives in adapters where the clamp is a single zener and the copper area of the drain node is less than ideal.
Where a 700 V super junction device earns its place
The first case is an offline converter on a 380 V to 400 V bus where the transformer has significant leakage and the clamp is deliberately loose, because the extra 100 V of blocking margin is cheaper than a better transformer. The second is a power factor correction stage in a lighting driver that has to survive a 10 per cent mains overvoltage plus the switching overshoot, where a 650 V device is at the edge of its rating and a 700 V device is not. The third is a snubberless flyback in a charger below 60 W, where 8 A of pulse current and 330 mJ of avalanche cover the start up and the short circuit event.
It is a poor choice for a synchronous rectifier or a load switch, where 0.560 ohm is far too high, and for a bridge at high frequency, where the 55 ns diode and the 2300 pF input capacitance set losses that a lower voltage part avoids. The part wants to be a single switch in a converter, not a switch in a pair.
Sourcing notes and the second source question
The second source for a 700 V part is usually a 650 V part offered as an upgrade, and that substitution runs the other way. A buyer who accepts a lower voltage to gain resistance is trading blocking margin for efficiency, which is a decision about the transformer and the clamp rather than about the bill of materials. Our power management cross reference keeps the voltage, the avalanche energy and the diode rows in the same view, so that trade is visible before a sample is ordered.
Where the original device has been discontinued or is on allocation, the obsolete part cross reference hub collects the substitutions that have already been checked for package and pinout, and it names the rows that have to be re-measured on the customer's board rather than assumed: the clamp energy, the gate loop ringing and the temperature rise on the actual pad.
Questions we answer before a reel is booked
The first question is whether 8 A is a continuous figure. It is not; it is a case temperature rating, and continuous current in still air is nearer 1.6 A. The second is whether a 650 V part can be used instead. It can, with 0.240 ohm and 15 A, but only if the transformer leakage and the clamp are good enough that the 650 V rating is never approached at turn off, and that is a measurement rather than an opinion.
The third question is about the gate. The threshold reaches 4.0 V, so a 3.3 V drive leaves no overdrive at the cold corner and a 10 V rail is the intended condition. The fourth is about the diode: 110 ns of worst case recovery at 100 A per microsecond is fine for a flyback and not for a hard switched bridge.
On supply, the TO-252 tape follows the standard outline, the reflow peak is 260 C for 10 seconds, and the date code and moisture level travel with the reel. Incoming inspection samples the on resistance at a 10 V gate, the threshold at 250 microamp, the breakdown at 250 microamp and the gate leakage at 20 V, and the avalanche row is verified on a sample basis because it is a destructive test.