VBE165R15SE
Product Specifications
VBE165R15SE
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBE165R15SE from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBE165R15SE: 650 V at 15 A and 220 milliohm by deep trench
The VBE165R15SE is a single N channel MOSFET in TO252 rated at 650 V, plus or minus 30 V on the gate, 15 A of drain current, with a threshold of 3.5 V and 220 milliohm at a 10 V gate. The catalogue names the technology as SJ_Deep-Trench rather than multi epitaxial.
Same voltage class as the 5 A part, a fifth of the resistance and three times the current. The difference is die area and column construction, and the two routes to a superjunction behave differently in the ways that matter to a power supply: charge balance, diode recovery and dV/dt ruggedness.
Two hundred and twenty milliohm at 15 A is 49.5 W, so the 15 A figure is again a case temperature number. At 4 A the loss is 3.5 W, which a DPAK with a copper plane can pass.
Key data for the VBE165R15SE
| Configuration | Single N channel |
| Package | TO252, DPAK, exposed drain tab |
| VDS | 650 V |
| VGS | Plus or minus 30 V |
| Vth | 3.5 V |
| ID | 15 A |
| RDS(on) at 10 V | 220 milliohm |
| Technology | Superjunction, deep trench |
| Body diode | Intrinsic, low forward drop, hard recovery |
| Gate charge | Larger than the 5 A die, ask for the curve |
| Thermal path | Drain tab, this die needs a plane under it |
| Typical use | PFC, LLC primary, 400 V bus switching |
| Isolation | None, the tab is the drain |
Deep trench against multi epitaxial
A multi epitaxial column is built by growing and doping several layers in sequence, which is a slow and therefore costly process, and the column depth is set by how many layers are grown. A deep trench column is etched into one thick layer and refilled, which allows a deeper and narrower column with better charge balance.
Better balance means a lower resistance for the same breakdown voltage and a softer resistance curve near the rated voltage. It also means the electric field is shaped more sharply, so the dV/dt and the avalanche behaviour need more care, and the diode recovery is not automatically better.
In practice the choice between the two is made on the supplier's process control and on the switching behaviour in the actual circuit. Two parts with the same 650 V and the same resistance can behave very differently at turn off, and the difference shows up as ringing and as losses in the clamp.
Two hundred and twenty milliohm in a PFC stage
A 150 W PFC at 400 V draws about 0.4 A RMS from the mains, and the switch carries a triangular current whose RMS is roughly a third of the peak. At 220 milliohm and 1.5 A RMS the conduction loss is 0.5 W, which is small against the switching loss at 65 kHz.
At 300 W the current doubles and the conduction loss quadruples, so the resistance starts to matter and the die size is right. Above 500 W a DPAK runs out of thermal headroom and the part moves to TO220 or TO247, which is why the body size is as much a limit as the die.
The diode recovery matters in a PFC only during the bridge commutation and in a bridgeless topology, where the body diode of one switch conducts before the channel takes over. In those topologies the recovery charge is a real loss and a real source of noise, and it has to be measured rather than assumed.
The other consequence of a larger die at 650 V is the reverse recovery of the body diode. Charge stored in the diode during conduction has to be removed when the voltage reverses, and in a hard switched bridge that removal is a current spike through the opposite switch. A 220 milliohm die stores more charge than a one ohm die because it is larger, and the spike is correspondingly bigger. In a PFC the diode conducts only during the bridge commutation and the spike is manageable. In a phase shifted bridge the diode conducts for the whole dead time and the spike becomes the dominant source of loss, which is why some converters parallel a fast diode with the channel even though the body diode already exists.
At 150 to 300 W the split between conduction and switching loss is worth measuring rather than estimating. At 65 kHz with a 400 V bus, a 220 milliohm die carrying 1.5 A RMS dissipates about 0.5 W in conduction and 1.5 to 2.5 W in switching, so the switching term dominates and a lower resistance die would not help. That is the point where the die size is already right and the next gain comes from the gate drive and the snubber rather than from the part.
Where the part fits and where it does not
It fits a 150 to 300 W PFC, an LLC primary in the same power class, a 400 V bus load switch, and a high voltage synchronous rectifier on the primary side of a phase shifted bridge. It does not fit a low side synchronous rectifier on a 12 V output, and it does not fit a bridge without checking the diode recovery and the dV/dt limit.
Our one stop BOM sourcing page covers how a power stage is bought as a group, because a 650 V switch is only as good as the gate driver and the clamp that come with it.
The sourcing side of this part is covered on the kitting service. For a power stage that goes to the line as a set, that page covers how the switch, driver and clamp are kitted together.
Questions we get on this code
Is 220 milliohm the 25 C figure? Yes, and a superjunction resistance rises steeply with temperature, so at 125 C it can be nearer 400 milliohm. Use the hot figure for a thermal calculation.
Can it replace the multi epitaxial part pin for pin? Mechanically yes, electrically the threshold and the capacitance differ, so the gate resistor and the dead time have to be rechecked.
What gate drive does it need? Ten volts is the specified point. A driver with a 10 to 12 V output and a separate turn off resistor keeps the switching loss and the dV/dt under control.
What should a purchase order carry? Part number, TO252, reel size and date code. We confirm the reel size on the quotation.