TMP423AQDCNRQ1
Product Specifications
TMP423AQDCNRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The TMP423AQDCNRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TMP423AQDCNRQ1 three channel remote plus local temperature sensor in the eight pin SOT-23
The TMP423AQDCNRQ1 is the three remote channel member of the TMP421 family, packaged in the eight pin SOT-23 with the DCN body. It carries one local sensor on the die and three remote channels that read diode connected transistors, which in practice are the thermal diodes built into processors, FPGAs, power stages or discrete transistors placed next to the heat source. The remote channels are the point of the part: a board that needs to watch three hot spots reads them all over one two wire bus instead of fitting three separate sensors.
The document prints one degree accuracy for the remote channels and one and a half degrees for the local channel, both as maxima, with series resistance cancellation, programmable non-ideality factor correction and diode fault detection. The non-ideality factor matters because the remote transistor is rarely an ideal diode; a processor thermal diode with a factor of 1.008 reads about two degrees cold if the sensor assumes unity, and the factor register is what removes that error without a calibration step on the line.
Key parameters taken from the TMP423AQDCNRQ1 document
| Channels | One local sensor on the die, three remote diode channels, DX1 to DX3 plus the common DXN |
| Remote accuracy | Plus or minus 1 C maximum, printed for multiple IC vendors with no calibration |
| Local accuracy | Plus or minus 1.5 C maximum |
| Resolution | 12 bit, 0.0625 C per code on both local and remote channels |
| Supply | 2.7 to 5.5 V for this member, 2.55 V is the floor of the C variant only |
| Bus | Two wire SMBus, write byte, read byte, send byte and receive byte commands |
| Addresses | Multiple interface addresses set by the A0 and A1 pins, so several devices share one bus |
| Remote range | Up to plus 150 C on the remote channels |
| Correction | Series resistance cancellation and a programmable non-ideality factor |
| Diagnostics | Diode fault detection on each remote channel, reported in the status register |
| Conversion | Programmable rate, eight conversions per second is the default setting in the document |
| Package | SOT-23, DCN, eight pins |
| Order code facts | TMP423AQDCNRQ1, SOT-23 DCN body, tape and reel, automotive Q1 grade |
| Family | The TMP421 has one remote channel, the TMP422 two and the TMP423 three, all in the same eight pin body |
The table above is read from the vendor document, not from a distributor summary. Where a window is printed, the window is what a production test should use, and the typical value is only a starting point for the first article.
Where the numbers matter in a real build
Series resistance cancellation is the feature that decides whether this part works on a long trace. A remote diode sits at the end of a pair of traces with a few ohms of copper and a connector in the way, and that resistance adds a voltage that looks like temperature. The document describes the cancellation sequence that injects two currents and removes the resistive term. It has a limit: past a certain series resistance the correction runs out of headroom, and the error comes back. On a board where the diode is more than a few tens of centimetres away, measure the series resistance in the actual harness and compare it against the document limit before assuming the feature covers it.
The non-ideality factor is a register, not a fixed number, so the value has to come from the device being monitored. Processor data sheets publish it, and where they do not, the honest approach is to measure one unit against a reference thermometer and write the factor into the production image per board type. Leaving it at the default is what produces the classic complaint that the reading is two degrees low at high temperature and correct at room, because the error term scales with absolute temperature.
Three remote channels on one bus means the conversion sequence and the fault handling have to be planned. A diode fault on one channel does not stop the others, so the firmware can keep controlling on two channels and raise a service flag on the third, which is a better behaviour than a single channel part that goes blind. The document prints the fault detection method and the status bits, and the first article should verify that unplugging one remote diode raises exactly that flag and no other.
The SOT-23 body carries the local sensor, and the local reading is the board temperature at the package, not the ambient. On a dense board the package sits close to a regulator and reads several degrees above the air, so a control loop that uses the local channel as if it were ambient will run the fan earlier than expected. That is board routing question: keep the part away from dissipating components when the local channel is meant to represent the enclosure, and accept the offset when it is meant to represent the board.
- Remote accuracy against a reference thermometer at 25, 60 and 100 degrees, with the non-ideality factor set from the monitored device document.
- Series resistance cancellation limit measured with the real harness length, not a bench lead.
- Diode fault flag on each channel, verified by opening one remote connection at a time.
- Address decoding with all devices on the bus populated, because two devices at one address is a silent fault.
- Local channel offset inside the finished enclosure against the air temperature the product specifies.
- Conversion rate and bus timing at the slowest supported clock, with the host at its production firmware setting.
Which projects this part fits
This part fits telecom and datacenter equipment where several processors sit on one board, storage controllers, projectors and display electronics, industrial drives with a separate power module, and any product where the thermal diode of a large device is the only temperature access available. For SUPERB customers building RF amplifiers, radar front ends and medical imaging electronics, the three channel version is often the cheapest way to add hot spot monitoring without adding three sensor packages and three sets of traces.
Questions that come up before a purchase order is released
Why three remote channels instead of three separate sensors?
Because the remote channels read diodes that already exist inside the processors and power devices, so nothing is added to those locations. The saving is not the sensor cost, it is the placement and the routing: one package and one bus instead of three parts, three placements and three sets of traces near hot copper.
What is the automotive suffix on this code?
The Q1 letter is the automotive qualification row for the SOT-23 body and the string ships on tape and reel. A catalogue row and an automotive row of the same family can differ in qualification and in temperature grade, so the order string should be copied exactly rather than assembled from a family table.
How far can the remote diode be?
The document states the cancellation range rather than a distance in centimetres, and the practical limit depends on the trace resistance and the noise pickup on the pair. A twisted pair to a remote board works at tens of centimetres; a long ribbon through a chassis usually does not without filtering, and the filter then has to be checked against the cancellation currents.
Is a pull up needed on the bus?
Yes, the two wire bus needs pull ups sized for the bus capacitance and the clock rate, and the part does not include them. With several devices on one bus the pull up is a single resistor pair, not one per device, and the value has to be chosen for the worst case capacitance rather than the typical.
What happens at power up before the host configures the part?
The part starts converting at its default rate and the default limit registers are set, so an unconfigured device can assert an alert if the board is already warm. If the alert pin drives a shutdown path, the firmware ordering matters, and the simplest guard is to mask the alert until the host has written the limit registers.
How SUPERB handles this line
We supply the TMP423AQDCNRQ1 on original tape and reel with lot traceability, and we verify the automotive letter and the body on the label before the parts are booked to a line. Where the question is which member of the family fits a given number of hot spots, the power management cross reference page lists the family side by side. Where the concern is continuity over a long production life, component obsolescence management covers the options, and incoming inspection plan covers the incoming checks that catch a mislabelled reel before it reaches the line.