VBE1410
Product Specifications
VBE1410
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBE1410 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBE1410: a 40 V, 12 milliohm N channel built for OR-ing
The VBE1410 is a single N channel MOSFET in the TO-252 body, printed at 40 V from drain to source with plus or minus 20 V on the gate, tested for gate resistance and unclamped inductive switching to the 2011/65/EU directive. On resistance is 0.012 ohm at a 10 V gate and 0.014 ohm at a 4.5 V gate, with the resistance rows quoted at 38.8 A and 37 A respectively. Continuous current is 45 A with the case at 25 C, 15.8 A with the ambient at 25 C and 12 A with the ambient at 70 C, and the part is package limited at 90 A. The vendor names OR-ing, server and DC to DC, which is a precise description of the job: a low resistance pass element on a redundant supply, where the forward drop is the loss and the 40 V rating covers a 12 V or 24 V rail with room for a transient.
The thermal figures explain the two current columns. Junction to case is 0.5 C per watt typical and 0.6 maximum, junction to ambient is 32 C per watt on a 10 second pulse and 40 maximum, and the dissipation is 100 W with the case at 25 C against 3.75 W in still air. At 20 A the die loses 4.8 W, which is 2.4 C on the case path and 192 C on the ambient path, so an OR-ing FET that carries real current has to be on copper with airflow or a heat spreader. The 45 A case rating is a statement about the tab and the heat sink, not about the reel.
The ratings a buyer checks first
| Drain to source voltage | 40 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate, 38.8 A | 0.012 ohm |
| On resistance at 4.5 V gate, 37 A | 0.014 ohm |
| Continuous drain current | 45 A at 25 C case, 15.8 A at 25 C ambient, 12 A at 70 C ambient |
| Pulsed drain current | 200 A |
| Continuous source to drain diode current | 90 A at 25 C case, 3.13 A at 25 C ambient |
| Power dissipation | 100 W at 25 C case, 75 W at 70 C case, 3.75 W at 25 C ambient |
| Junction to ambient, junction to case | 32 and 0.5 C per watt typical, 40 and 0.6 maximum |
| Gate threshold voltage | 1.5 V minimum, 2.5 V maximum |
| Total gate charge at 10 V gate, 38.8 A | 85 nC typical, 120 nC maximum |
| Input, output and reverse transfer capacitance | output 725 pF, reverse transfer 570 pF |
| On state drain current at 10 V gate | 90 A |
| Forward transconductance | 160 S |
| Gate leakage at 20 V | plus or minus 100 nA |
| Junction and storage range | minus 55 to plus 175 C |
Reading the electrical table instead of the front page
The threshold row is tight, 1.5 V to 2.5 V, so a 4.5 V drive has 2 V of overdrive on the worst case die and the 0.014 ohm row is real. The zero gate drain current is 1 microamp at 25 C and 10 microamp at 55 C, which is a large die with normal leakage, and the gate leakage of plus or minus 100 nA is unremarkable. What is remarkable is the reverse transfer capacitance of 570 pF against 725 pF of output capacitance: a ratio near one means the drain voltage couples strongly into the gate, the Miller plateau is long, and the gate drive has to be stiff. On an OR-ing stage, where the part is on continuously and switches only at insertion, this does not matter. In a switching stage it matters a great deal.
Gate charge is 85 nC typical and 120 nC maximum at a 10 V drive, which is a heavy gate for a small driver: at 200 kHz that is 17 mA of average gate current and 170 mW in the driver, and at 500 kHz it is 42 mA and 425 mW. The sheet prints only the 10 V row at this current, so a 4.5 V drive is not defined for charge and should not be assumed to halve. The forward transconductance of 160 S is the highest in this band and is what a low resistance die looks like when it is measured in the linear region.
The body diode is 90 A continuous with the case at 25 C and 3.13 A in still air, which is the largest diode rating of any part in this group and the reason the part suits a redundant supply: during a switchover the diode carries the load for a few microseconds and the channel takes over after. The sheet's avalanche rows do not resolve cleanly in the text layer, so no avalanche figure is quoted on this page. That is a gap in what can be read from the vendor print rather than a missing rating, and a converter that clamps its inductive energy does not depend on the number.
Where a 40 V, 12 milliohm switch earns its place
The first case is a redundant 12 V supply in a server or a storage shelf, where two rails are OR-ed through two of these and each carries half the load. At 15 A the die loses 2.7 W, the forward drop is 0.18 V, and the part is on continuously, so the thermal case is steady state rather than transient and the 3.75 W ambient figure is the ceiling. The second case is a 24 V battery path in an industrial product where the current is 10 A to 20 A and the 40 V rating covers a load dump clamp at 32 V.
The third case is a hot swap or a soft start on a 24 V rail, where the 200 A pulsed rating covers the inrush into a large capacitance and the 90 A diode rating covers the reverse current when the rail collapses. In all three the part is used as a pass element that is on almost all the time, and the rows that matter are the resistance at the gate voltage available, the ambient thermal path and the diode rating. The switching rows matter only at insertion, which is why a 570 pF reverse transfer capacitance is acceptable here and would not be in a converter.
Sourcing notes and the second source question
OR-ing FETs are compared on resistance at the drive the board provides and on the ambient thermal path, and two vendors can print the same 12 milliohm while one of them quotes it at 38 A and the other at 20 A with a wider temperature coefficient. Our power management cross reference keeps the test current and the thermal resistance in the same row as the resistance, so the comparison is made on the conditions the part will run at. Where a customer is looking at the total cost of a redundant supply rather than a single part, the route in how to reduce component cost sets out which rows can be traded and which cannot, and the thermal path is usually the one that cannot.
For a replacement in a qualified product, the tests that matter on an OR-ing stage are the forward drop at the real current, the switchover transient, the reverse current path through the diode and the junction temperature at the airflow the chassis provides. A part that matches the resistance but moves the diode forward voltage will change the switchover behaviour, and that is the difference a bench test finds and a datasheet comparison does not.
Questions we answer before a reel is booked
The first question is whether 45 A can be carried continuously. It can with the case held at 25 C and a heat sink on the tab, and in still air the same part is a 3.75 W device, which at 0.012 ohm is about 17 A. The second question is whether the 4.5 V resistance row can be used at 4.5 V. It can, but the gate charge at that drive is not printed, so the driver budget has to be based on the 120 nC maximum at 10 V rather than on a halved figure.
The third question is about the diode in a redundant supply. The 90 A continuous diode rating with the case at 25 C is a transient figure for a switchover and 3.13 A is the still air figure, so the diode is a path for microseconds and not for a sustained reverse current. The fourth is about avalanche, which is not quoted here because the vendor print does not resolve in the text layer, and a customer who needs a number should take it from the printed page rather than from a distributor summary.
On supply, the reel is quoted with the date code on the label and the moisture level from the packing list, the reflow window is a 260 C peak, and incoming inspection samples the on resistance at 10 V and 4.5 V, the threshold at 250 microamp and the diode forward voltage. A build that needs the part to match an existing thermal model should book the tab solder process as part of the qualification, because the 0.5 C per watt junction to case is only true when the tab is fully wetted.