VBE1102N
Product Specifications
VBE1102N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBE1102N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBE1102N: a 100 V N channel in TO-252 for the 30 A class
The VBE1102N is a single N channel MOSFET in the TO-252 body, printed at 100 V from drain to source with plus or minus 20 V on the gate, tested for gate resistance and unclamped inductive switching. On resistance is 0.0185 ohm at a 10 V gate with 15 A flowing, and the part is package limited at 30 A, with a 140 A pulsed rating and a 101 mJ single pulse avalanche energy. The vendor files it under primary side switch and isolated converter. That placement is the honest one: 0.0185 ohm is twice the resistance of the 8.5 milliohm member of the same family, so this part is for the case where 15 A to 20 A is enough and the board would rather spend the money elsewhere.
The thermal path is the same TO-252 as its lower resistance sibling: 0.85 C per watt junction to case typical and 1.1 maximum, 40 C per watt junction to ambient on an FR4 pad, 136.4 W of dissipation with the case at 25 C and 3 W in still air at 25 C. The current that a board can really carry therefore depends almost entirely on the copper under the tab. At 15 A the die loses 4.2 W, which is a 167 C rise on the ambient path and 4.6 C on the case path, so the difference between a 1 cm square pad and a 5 cm square pad is the difference between a working supply and a thermal shutdown.
The ratings a buyer checks first
| Drain to source voltage | 100 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate, 15 A | 0.0185 ohm |
| Continuous drain current | 30 A, package limited |
| Pulsed drain current | 140 A |
| Continuous source to drain diode current | 35 A at 25 C case |
| Single pulse avalanche energy | 101 mJ into 0.1 mH |
| Power dissipation | 136.4 W at 25 C case, 68.2 W at 100 C case, 3 W at 25 C ambient |
| Junction to ambient, junction to case | 40 and 0.85 C per watt typical, 50 and 1.1 maximum |
| Gate threshold voltage | 2.5 V minimum, 5 V maximum |
| Total gate charge at 10 V gate | 38 nC typical |
| Gate source and gate drain charge | 14 nC and 12 nC |
| Input, output and reverse transfer capacitance | 2400, 230 and 80 pF |
| Gate resistance | 1.6 ohm typical, 2.5 maximum |
| Body diode forward voltage at 15 A | 0.85 V typical, 1.5 V maximum |
| Junction and storage range | minus 55 to plus 175 C |
Reading the electrical table instead of the front page
The threshold row is the first surprise: 2.5 V minimum and 5 V maximum at 250 microamp. A 5 V gate drive therefore sits exactly at the maximum threshold on a worst case die, which is the definition of a part that will not turn on reliably from logic. This is a 10 V gate device and the sheet only prints one resistance row because that is the only drive the vendor wants to guarantee. A board that drives the gate from 4.5 V will see a resistance well above 0.0185 ohm and a spread between units that no incoming test will filter out.
Gate charge is 38 nC typical with 14 nC of gate source charge and 12 nC of gate drain charge, which is a light load for a die of this area and the reason the switching rows are short: 12 ns turn on delay and 10 ns rise, 18 ns turn off delay and 8 ns fall, measured at 50 A with a 1 ohm gate resistor. Add the 1.6 ohm internal gate resistance and the external resistor that keeps the edge quiet, and the part switches in tens of nanoseconds, which is fast enough that the routing of the gate loop matters more than the resistor value. The 2400 pF input capacitance and 80 pF reverse transfer capacitance give a Miller ratio of thirty to one, so the drain voltage barely couples into the gate.
The body diode is 0.85 V typical and 1.5 V maximum at 15 A, with 80 ns recovery and 160 nC to 240 nC of recovered charge. That charge is larger than the gate charge of the part, which is worth pausing on: on a synchronous stage the recovery loss can exceed the drive loss, and at 100 kHz a 240 nC maximum is 24 mA of equivalent loss current. For a hard switched converter the diode is a real part of the budget; for a converter that turns on into zero voltage it is not. Avalanche energy of 101 mJ into 0.1 mH covers a modest leakage inductance and is half the rating of the 8.5 milliohm member, which is consistent with a smaller die.
Where a 100 V, 18.5 milliohm switch earns its place
The first case is a 48 V to 24 V or 48 V to 12 V isolated converter in the 200 W to 400 W class, where 15 A on the primary is the whole load and the resistance at 10 V is acceptable because the duty cycle is short. The 100 V rating leaves room for the leakage spike and the 101 mJ avalanche row covers the energy the clamp does not. At 10 A the die loses 1.85 W, which on the case path is 2 C and on the ambient path is 74 C, so the tab has to be soldered to copper and the copper has to be connected to something.
The second case is a 72 V battery path or a 60 V industrial rail where the current is modest and the priority is a part that survives a load dump without a snubber. A third case is a low side switch in a motor drive that runs at 48 V and a few amps, where the 140 A pulsed rating covers the stall current and the 2.5 V minimum threshold means a 5 V drive is marginal but a 10 V drive is comfortable. In all three the part is chosen for its voltage margin and its body, not for the resistance.
Sourcing notes and the second source question
A 100 V TO-252 part with a 5 V threshold maximum is a case where a replacement can look better on paper and behave worse on the board. Our power management cross reference keeps the threshold maximum, the gate charge and the diode recovery charge in the same row as the resistance, so the comparison is made at the drive the customer actually has. When a competitor code arrives, the four rows we compare first are the resistance at the gate voltage in use, the threshold maximum, the recovered charge and the avalanche energy.
Where the part has to be proven before a build, how to verify a drop in replacement sets out the tests that catch the usual problems on a primary switch: gate ringing at the new charge, the leakage spike against the clamp, diode recovery on the secondary side and junction temperature on the real tab area. This family publishes no orderable addendum, so no reel size, moisture level or marking code is quoted on this page, and a customer who needs a date code window has to book it rather than find it on a mixed shipment.
Questions we answer before a reel is booked
The first question is whether the part can be driven from 5 V logic. It cannot be relied on: the maximum threshold is 5 V, so a 5 V drive has no guaranteed overdrive and the resistance row is not defined at that gate voltage. The second question is whether 30 A can be carried. It can with the case at 25 C and a heat spreader, and in still air the same part is a 3 W device, which at 0.0185 ohm means about 13 A before the junction reaches its limit.
The third question is about the body diode in a synchronous application. The 35 A continuous diode rating is adequate for the freewheel current at 15 A, and the recovered charge is the row that sets the loss, not the forward voltage. The fourth is about avalanche. The 101 mJ rating is a single pulse into 0.1 mH and it derates with junction temperature and repetition rate, so a converter that relies on it instead of a clamp is a reliability problem waiting for a field return.
On supply, the reel is quoted with the date code on the label and the moisture level from the packing list, the reflow window is a 260 C peak, and the TO-252 tab has to be soldered rather than glued for the thermal figures to mean anything. Incoming inspection samples the on resistance at 10 V, the threshold at 250 microamp and the diode forward voltage at 15 A.