VBA1210
Product Specifications
VBA1210
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBA1210 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBA1210: a 30 V N channel in an SO-8 for high side switching
The VBA1210 is a single N channel MOSFET in the SO-8 body, printed at 30 V drain to source and plus or minus 20 V on the gate, with 8 milliohm at a 10 V gate and 11 milliohm at 4.5 V. It carries 13 A at a 25 C case, 10 A at 70 C, 9 A at a 25 C ambient and 7 A at 70 C, with a 45 A pulse rating. The vendor summary marks the part as optimised for high side synchronous rectifier operation and lists notebook CPU core high side switch as the application, which is the use this die was shaped for: a 20 A class buck converter switching at a few hundred kilohertz, where the low side is a bigger die and the high side is this one.
The four drain pins in the SO-8 are what make 8 milliohm possible in this body. Current enters through four leads and leaves through three source leads, so the package resistance is a fraction of a single lead part and the heat path runs into the board through all of them. In a notebook class converter that is the difference between a part that needs a heatsink and one that does not.
The rows a buyer checks first
| Drain to source voltage | 30 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate | 8 milliohm at 10 A |
| On resistance at 4.5 V gate | 11 milliohm at 9 A |
| Continuous drain current | 13 A at 25 C case, 9 A at 25 C ambient |
| Pulsed drain current | 45 A |
| Continuous source current, diode | 3.7 A at 25 C case, 2.0 A at 25 C ambient |
| Power dissipation | 4.1 W at 25 C case, 2.2 W at 25 C ambient |
| Power dissipation at 70 C | 2.5 W at the case, 1.3 W in ambient |
| Gate threshold voltage | 1.0 V minimum, 3.0 V maximum |
| On state drain current | 20 A at a 10 V gate |
| Forward transconductance | 50 S at 10 A |
| Total gate charge at 10 V | 15 nC typical, 23 nC maximum |
| Gate to drain charge | 2.3 nC |
| Body diode forward voltage | 0.8 V typical, 1.2 V maximum |
What the electrical table adds to the summary
The threshold window runs from 1.0 V to 3.0 V at 250 microamp, which is wide for a 30 V part and normal for this class of die. A 4.5 V gate drive therefore turns the part on with margin, and a 10 V drive is better still. The gate charge of 15 nC typical and 23 nC maximum with about 2.3 nC of gate to drain charge is the number that matters in a high side socket: the driver has to charge that gate from a rail that sits above the input, and every nanocoulomb is current drawn from the bootstrap capacitor. At 500 kHz a 23 nC gate at 5 V is 115 milliwatt of drive loss, and the bootstrap capacitor has to be sized for the charge per cycle rather than for the average.
The on state drain current of 20 A at a 10 V gate and the transconductance of 50 S tell the reader that the die is large for its rating. That is the point of a high side part: it runs at a duty cycle of 20 to 40 per cent in a buck, so its conduction loss is small, but its switching loss happens at every edge and its gate charge has to be small relative to the current it carries. The 8 milliohm at 10 A gives 0.8 W of conduction loss, which the SO-8 body can pass into the board without a heatsink at a 25 C ambient.
The leakage rows are 1 microamp at 25 C and 10 microamp at 55 C, and the body diode forward voltage is 0.8 V typical and 1.2 V maximum. Continuous diode current is 3.7 A at a 25 C case and 2.0 A at a 25 C ambient, which is the limit during the dead time in a synchronous stage: a controller with a long dead time forces the full inductor current through this diode at the start of every cycle, and a part rated for 2 A in ambient will not survive a 10 A inductor current for long.
Where this die earns its place
The first use is the high side of a notebook or tablet buck converter running from a two cell or three cell pack at 8 to 20 V, with a 1 to 3 MHz switching frequency and a low side part with a much lower resistance. The second is a POL converter on a board where the 30 V rating covers a 24 V input with margin and the 8 milliohm keeps the conduction loss low at 5 A. The third is a battery disconnect in a handheld product, where the part sits in the main path and its low resistance keeps the drop under 100 mV at 10 A.
In an LED driver or a small motor drive the part works as the low side switch instead, and the 45 A pulse rating covers the inrush and the stall current. The limitation is the 30 V rating: a 24 V rail with a transient can reach 35 V, and a 40 V part is the honest choice there. A 12 V rail with a well clamped input is the comfortable operating point, and most of the notebook class converters this die was made for run at 20 V or below.
Sourcing notes and the second source question
A 30 V SO-8 with 8 milliohm is one of the most competitive parts in the catalogue, and the substitutes differ in the rows that decide the switching loss rather than the conduction loss. Gate charge, gate to drain charge and threshold maximum are the three that change behaviour in a high side socket, because a part with 40 per cent more gate charge loads the bootstrap and a part with a higher threshold turns on later in the cycle, which shifts the whole loss split between the two switches. Our power management cross reference tables those rows against the drive voltage the customer actually has.
The incoming record matters more here than on a larger part, because a re marked SO-8 with a smaller die passes a curve trace at room temperature and fails at 100 C. The plan in incoming inspection plan covers the sample size, the on resistance check at 4.5 V, the gate charge sample and the X ray of the die attach. We supply this code on the standard reel with the date code on the label and hold a per lot record for the customer who needs to match a qualified build.
Questions we answer before a reel is booked
Buyers ask whether 13 A can be held continuously. It can at a 25 C case with the drain pins soldered to a large copper area, and the ambient figure is 9 A at 25 C and 7 A at 70 C. The second question is whether the part can be driven from a 4.5 V rail. It can, at 11 milliohm, and the penalty against 8 milliohm is 37 per cent more conduction loss, which in a high side socket with a 30 per cent duty cycle is 11 per cent of the total conduction loss.
The third question concerns the diode rating of 3.7 A. In a synchronous buck the high side body diode never conducts in normal operation, because the inductor current flows through the low side switch during the dead time. It conducts only at start up and during a fault, which is why the rating looks low for a part that carries 13 A. A converter that runs in discontinuous mode at light load reverses that, and the diode then carries the full inductor current for part of every cycle.
On supply, this code is a catalogue item with the reel size and date code on the label. We hold an incoming record with an on resistance sample at 4.5 V, and where a customer needs a date code window for a product already qualified, the booking has to be made before the order is placed rather than after the parts land.