HXNM40003
Product Specifications
HXNM40003
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXNM40003 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXNM40003: thirty six decibels of output with twenty five decibels of gain
The HXNM40003 is a member of the Hisiwell high gain family, which is a different proposition from the standard internally matched parts. The vendor index row reads 2.7 to 3.1 GHz, saturated output at least 36 dBm, gain at least 25 dB, drain efficiency at least 40 per cent, 28 V drain rail, continuous wave. That is 3.98 W of output with a gain floor four decibels above anything in the standard family at the same power.
The gain is the whole argument. With 25 dB the drive for rated output is 11 dBm, which is 13 mW. A synthesizer, a modulator output or a small MMIC driver reaches 11 dBm directly, so the part can be the only amplifier in the transmit chain after the signal source. Two stages become one, and the board loses a driver, its bias network and its own thermal path.
The power budget is small. At 40 per cent efficiency 3.98 W of output draws 10.0 W from the rail, which is 0.355 A at 28 V, and leaves 6.0 W of heat. Those are calculated figures from the published rows, and the dissipation is low enough that a board level carrier handles it without a separate spreader.
The band is the other half of the story. 2.7 to 3.1 GHz covers the S band radar allocations, the 3 GHz point to point links and the lower part of the S band satellite service. Four hundred megahertz at a 2.9 GHz centre is 13.79 per cent fractional bandwidth, which is wide for an internally matched part and wide enough to cover a whole radar band with one amplifier.
The parameter rows Hisiwell publishes for HXNM40003
| Part class | Gallium nitride power transistor, internally matched, high gain family |
| Frequency range | 2.7 to 3.1 GHz |
| Bandwidth, calculated | 400 MHz, 13.79 per cent fractional at a 2.90 GHz centre |
| Saturation output power as published | at least 36 dBm |
| Saturation output power in watts, calculated | 3.98 W |
| Gain as published | at least 25 dB |
| Drain efficiency as published | at least 40 per cent |
| Drain voltage | 28 V |
| Flatness across the band | not published, the index prints a slash in that column |
| Operating mode | continuous wave |
| Output at 1 dB compression | not published, the index prints a slash in that column |
| DC input at saturation, calculated | 10.0 W |
| Drain current at saturation, calculated | 0.355 A at 28 V |
| Dissipation at saturation, calculated | 6.0 W |
| Dissipation if efficiency falls to 30 per cent, calculated | 9.3 W |
| Drive power for the rated output, calculated | 11 dBm, 12.6 mW |
| Output per 100 MHz of the band, calculated | 1.00 W |
| Load voltage at saturation into 50 ohm, calculated | 14.1 V RMS, 20.0 V peak |
| Thermal resistance, junction to case | not published |
| Package outline and dimensions | not published in text |
| Scattering parameters | not published |
| Stability data and load mismatch tolerance | not published |
| Pinch off voltage and gate bias point | not published |
| Operating and storage temperature | not published |
| Orderable addendum and packing | not published |
| Family neighbour at 40 dBm on 2.7 to 3.5 GHz | HXNM40004, same rail, 28 dB gain |
What twenty five decibels of gain does to the chain
A conventional 4 W part at this frequency offers 10 to 14 dB of gain and needs a driver at 22 to 26 dBm. That driver needs its own driver or a high output source, and each stage brings a bias network, a filter and a thermal path. At 25 dB the HXNM40003 takes 11 dBm and the chain collapses to one stage.
The saving is not only parts. A single stage has one compression point to characterise, one bias point to set and one thermal path to prove. A two stage chain has three of each, plus the interstage match that sets the overall flatness. For a product built in the hundreds rather than the thousands, that simplification is worth more than the last decibel of efficiency.
The cost is stability margin. High gain parts are harder to keep unconditionally stable, and the vendor publishes no stability data and no load mismatch tolerance. A 25 dB part driving a filter that presents an open circuit at some out of band frequency can oscillate, and the usual cure is a resistive pad or an isolator at the output.
The gain also falls with temperature, and no gain temperature coefficient is published. A part with 25 dB at 25 C may have 23 dB at 85 C, which would change the drive requirement by 2 dB. A system that runs the source at a fixed level should check the gain at the top of its temperature range rather than assume the 25 dB floor holds there.
S band radar and the 2.7 to 3.1 GHz window
The S band radar allocations sit inside this window in most regions, and 3.98 W is a useful level for a short range radar, for a radar altimeter or for a laboratory radar target simulator. The 400 MHz span covers the whole allocation with margin, so a product can be tuned to a channel by filter rather than by amplifier.
The continuous wave rating matters for a radar simulator, which transmits continuously rather than in pulses. A pulsed radar part used in a simulator has to be derated for continuous wave, and this part does not carry that compromise because it is published as continuous wave from the start.
The 13.79 per cent bandwidth is wide for an internally matched part and it is achieved with a gain of 25 dB, which is unusual together. The usual trade is gain against bandwidth, and this family appears to get both by matching on the carrier rather than on the board, which is the same construction the standard family uses.
Where the application is a communications link rather than a radar, the same window covers the 3 GHz point to point allocations. A 4 W stage with 25 dB gain and 14.1 V RMS of load voltage is a comfortable fit for a small outdoor unit, and the drive can come straight from the modem output.
Thermal and bias notes at four watts
6.0 W of dissipation is low enough that the carrier choice is not critical. On 5 C per watt the rise is 30 C over the case and on 3 C per watt it is 18 C, so even a modest sink holds the case inside a 100 C limit at a 70 C ambient. What matters more is the local heating of the gate network, which is not covered by any published figure.
The gate bias point is not published, and with 25 dB of gain the bias setting is more sensitive than on a low gain part. A small change in quiescent current moves the gain and the compression point together, so the bias supply needs to be stable and the first article needs a bias sweep recorded rather than a single point noted.
The load voltage at 3.98 W into 50 ohm is 14.1 V RMS and 20.0 V peak, below the 28 V rail and inside the rating of ordinary connectors. That is one less constraint on the mechanical build compared with the 50 W members of the standard family.
No moisture level is published, which matters for assembly. A part that needs baking changes the build flow, and for a production program the level should be confirmed with the factory before the assembly process is fixed. The same request can confirm the packing and the marking.
The high gain family across the bands
Hisiwell publishes nine parts in this family, and the gain ranges from 18 to 28 dB. HXNM40004 is the 40 dBm member on 2.7 to 3.5 GHz with 28 dB gain, HXNM40007 and HXNM40008 are the 4.4 to 5 GHz pair at 40 and 43 dBm, and HXNM40012 covers 8 to 12 GHz at 42 dBm with 20 dB gain.
The pattern is that gain falls as frequency rises. Twenty eight decibels at 3 GHz, 23 to 26 dB at 4.4 to 5 GHz, 18 to 20 dB at 5.1 to 12 GHz. A system engineer comparing members of the family should compare gain at the band of interest rather than assuming the family number carries across.
The power range is narrower than the standard family. This family runs from 33 to 44 dBm, while the standard family runs from 36 to 58 dBm. Where the requirement is above 44 dBm, the high gain family is not the answer and the standard family is.
For a cross reference the family number is the first thing to check, because a high gain part and a standard part with the same output are not interchangeable in a chain that was built around a driver. Our RF power transistor cross reference page puts the gain column next to the power column for that reason.
Questions buyers ask about HXNM40003
Is the 36 dBm saturation or compression. The index prints 36 dBm in the saturation column and a slash in the compression column, so the figure is saturation. No compression point is published.
What is the flatness across 400 MHz. Not published. The index prints a slash in the flatness column for this part, unlike the standard family which carries plus or minus 0.8 dB. A system that needs a known flatness has to measure it on the first article.
Can it drive a larger stage. It can, and that is a sensible use. Four watts with 25 dB gain is enough to drive a 20 to 50 W stage at 2.9 GHz, and the pair replaces a three stage chain with two. The interstage match is then the item that sets the overall flatness.
How is it supplied. With no addendum, no packing column and no moisture level on the vendor page, the purchase order names the band, the rail and the quantity and the factory confirms the rest. Where the part is needed against a radar program schedule, the defense grade components route covers the traceability and the holding arrangement that such a program normally requires.