SSM3582ACPZ-R7
Product Specifications
SSM3582ACPZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The SSM3582ACPZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
SSM3582ACPZ-R7: 2 x 14.4 W from a 16 V rail and the heat that comes with it
The SSM3582ACPZ-R7 is the Analog Devices stereo Class-D audio amplifier with a digital input, a filterless sigma-delta modulator and an I2C control port, supplied from a single rail of 4.5 V to 16 V. Two channels deliver 14.4 W each into 8 ohm at 16 V and 14.67 W each into 4 ohm at 12 V, both at less than 1 percent THD+N. In mono mode one channel reaches 49.69 W into 2 ohm at 16 V. The 2 x 31.76 W in the part title is the two channel figure at the top of the rail into a 4 ohm load; the number a stereo 8 ohm speaker sees is 2 x 14.4 W. Internal LDOs run the analog and digital blocks from the same PVDD, or an external 5 V and 1.8 V can be supplied for the lowest consumption. It sits in the analog and mixed-signal IC line card with the converters and codecs that usually feed it.
The loss figure decides the enclosure, not the output figure
At 93.8 percent efficiency into 8 ohm, 2 x 14.4 W of output means 30.70 W drawn from the rail and 1.90 W left in the package and the output filter. Into 4 ohm at 12 V the efficiency drops to 90.6 percent, so 2 x 14.67 W draws 32.38 W and leaves 3.04 W of heat. The quiescent current of 12.34 mA at 12 V adds 0.15 W before any audio is played. That is a small package with a thermal pad, so the pad area and the copper it sits on are part of the power rating; a 3 W loss in a sealed plastic case raises the junction well above the ambient the datasheet test used.
| Parameter | Vendor figure | What it works out to |
|---|---|---|
| Supply range | 4.5 V to 16 V single rail | one rail for both channels |
| Output per channel | 14.4 W into 8 ohm at 16 V | 10.73 V rms, 15.18 V peak |
| Headroom at 16 V | peak 15.18 V against 16 V | 0.82 V between rail and peak |
| Efficiency | 93.8 percent at 8 ohm, 90.6 percent at 4 ohm | 1.90 W loss against 3.04 W loss |
| Noise | 38.5 uV rms A-weighted | 108.9 dB below 14.4 W into 8 ohm |
| SNR and THD+N | 106.5 dB, 0.004 percent at 5 W | 17.4 bits of usable dynamic range |
| Load floor | 3 ohm stereo, 2 ohm mono | 5 uH minimum load inductance |
Why the noise figure and the SNR figure do not agree
The 106.5 dB signal to noise ratio is quoted against a defined full-scale output, while the 38.5 uV rms A-weighted noise is an absolute figure. Placed against the 10.73 V rms that 14.4 W into 8 ohm represents, that noise is 108.9 dB down, which is better than the ratio in the headline. The two are measured under different gain and filter settings, so a system noise budget should use the absolute microvolt figure and the real speaker sensitivity, not the dB number. Against a 24-bit input stream the modulator cannot deliver 24 bits: 106.5 dB is 17.4 bits, so the bottom 6 bits of the digital word sit below the analog noise floor.
Digital side, addressing and lifecycle
- The serial port takes I2S, left justified or TDM, with the TDM slave mode addressing up to 16 devices on one bus and up to 16 pin-selectable I2C addresses.
- Sample rates run from 8 kHz to 192 kHz at 24-bit resolution, so a 48 kHz build and a 96 kHz build share the same order code.
- The part is marked not recommended for new designs on the vendor page. For a running product that is a supply question rather than a performance question, and it is the reason to keep a second source on file.
Questions buyers ask
Is 2 x 31.76 W the stereo rating? It is the stereo rating at 16 V into 4 ohm. At 12 V into 4 ohm the same two channels give 2 x 14.67 W, and into 8 ohm at 16 V they give 2 x 14.4 W each.
What has to change to move from 12 V to 16 V? The rail, the full-scale setting in the I2C registers, and the thermal budget. Output rises from 14.67 W to 14.4 W into a different load, so the loudest change is the impedance, not the voltage.
For quantities of this amplifier or a pin-compatible alternative from stock, send the target quantity and the rail voltage. Audio parts for portable and medical products are listed under medical device components, and the amplifier families we hold cross references for are on the amplifier cross reference page.
Request Quote — In Stock, 100% New & Original, Full Warranty