Contact Us

OP2177ARZ-REEL

Brand: Analog Devices
Analog Devices OP2177ARZ-REEL is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

OP2177ARZ-REEL — Analog & Mixed-Signal ICs | Superb Automation

OP2177ARZ-REEL

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The OP2177ARZ-REEL from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

OP2177ARZ-REEL: 60 uV of offset, 2 nA of bias, and the 30 kohm where the two swap places

The OP2177ARZ-REEL is the dual member of the OP1177 precision family in the 8-lead SOIC_N body, supplied on tape and reel. It is a 60 uV maximum offset amplifier with 0.7 uV per degree C of drift, 2 nA of maximum input bias current, 8 nV per root hertz of voltage noise and 400 uA of supply current per amplifier. The number that decides whether it is the right part for a build is not the offset, it is the source resistance: the two error terms cross at roughly 30 kohm.

Published values

ParameterValue
Offset voltage60 uV maximum
Offset voltage drift0.7 uV per degree C maximum
Input bias current2 nA maximum
Input voltage noise8 nV per root hertz typical
Low frequency noise0.4 uV peak to peak, 0.1 Hz to 10 Hz
Common mode rejection118 dB minimum on the dual, 120 dB on the single
Power supply rejection114 dB minimum on the dual, 120 dB on the single
Supply rangeplus or minus 2.5 V to plus or minus 15 V
Supply current400 uA per amplifier typical, 500 uA maximum
Gain bandwidth product1.3 MHz
Slew rate0.7 V per microsecond
Package8-lead SOIC_N, R suffix, tape and reel

Sixty microvolts is 0.39 LSB at 16 bits on a 10 V span, and drift is larger

A 16-bit converter on a 10 V span has a least significant bit of 152.6 uV, so 60 uV of offset is 0.39 LSB and the offset alone does not break a 16-bit measurement. The drift term does: 0.7 uV per degree C over the 125 degree C industrial span is 87.5 uV, which is 0.57 LSB and larger than the offset the part is bought for. A board trimmed at 25 degree C therefore does not hold 16-bit accuracy at 85 degree C, and the trim has to be either temperature compensated or accepted as a one point correction.

The same arithmetic applies to the common mode and supply rejection. At 120 dB minimum, a 5 V common mode change appears as 5 uV at the input and a 1 V supply change as 1 uV, both smaller than the drift, so on a quiet rail the drift is the term that matters.

Two nanoamps crosses the offset at about 30 kohm of source resistance

Two nanoamps into 1 Mohm is 2 mV, thirty three times the offset limit, so a part chosen for 60 uV on a megohm source gets a 2 mV error instead. Into 10 kohm the same current is 20 uV, a third of the offset. The crossover is 60 uV divided by 2 nA, or 30 kohm: below it the offset dominates, above it the bias current does.

That is the whole selection rule for this family. Thermocouples, resistance temperature detectors, strain bridges and shunt measurements are listed by the vendor as applications, and the ones that actually benefit are the bridge and detector circuits that sit in the tens of kilohms. A 350 ohm bridge at 5 V draws 14 mA and is a fine load for this amplifier, while a 10 Mohm detector is not: that case needs a CMOS or JFET input part with picoamp bias, and the lower offset of the bipolar input stops being the deciding figure.

1.3 MHz and 0.7 V per microsecond are two separate ceilings

At a gain of 100 the 1.3 MHz product gives 13 kHz of closed loop bandwidth. The slew rate gives a second limit: 0.7 V per microsecond across a 10 V peak to peak swing is 22.3 kHz of full power bandwidth, because the fastest a sine can move is 2 pi f times its peak amplitude, 5 V here. At a gain of 100 the gain bandwidth arrives first, at 13 kHz. At unity gain the slew rate arrives first, so the two figures are checked against the gain the circuit actually uses.

Eight nanovolts per root hertz over a 10 kHz band is 0.8 uV RMS and over 100 kHz it is 2.5 uV RMS, both above the 0.4 uV peak to peak of low frequency noise. On a source above 30 kohm the resistor noise dominates anyway: 30 kohm at 300 K is 22 nV per root hertz, nearly three times the amplifier, so a lower noise amplifier buys nothing at that impedance.

What the ARZ-REEL suffix says about the body

The R suffix is the 8-lead SOIC_N body and RM is the 8-lead MSOP, so the same dual amplifier is available in two footprints that are not interchangeable on an existing board. ARZ is the RoHS finish and REEL is the tape and reel packing. The MSOP and the TSSOP bodies are supplied on tape and reel only, which is worth knowing when a small quantity is ordered for a prototype: a cut length from a reel is normal, a tube is not available.

The single and quad members of the family share the same core, so a build that needs one more channel moves to OP4177 in the 14-lead body rather than paralleling two duals. Paralleling adds the offset of both devices in series with the gain setting network, which is the wrong direction for a precision front end.

Sourcing notes for this family: the amplifier cross reference holds the cross references, the pin to pin cross reference is the pre substitution check, and component lead time solutions is what we use when the part on the drawing is not on the shelf.

Two questions buyers ask

Is the dual the same die as the single? It is the same amplifier core in a two channel body, with the same offset, drift and noise specification, but the rejection limits are stated per channel and the dual carries a 118 dB common mode minimum and 114 dB of supply rejection where the single is quoted at 120 dB for both. A substitution between the two changes the pin count, so it is a board change and not a drop in.

Can it run from a single 5 V rail? The supply range is printed as plus or minus 2.5 V to plus or minus 15 V, which is a 5 V total span at the bottom of the range, so a single 5 V rail is inside it. What changes is the headroom at both ends: the inputs and the output stop short of the rails, and the data sheet specifies the swing into a 2 kohm load at the dual supplies, so a single rail build has to check the swing against the converter it drives rather than assuming it.