Contact Us

OP07DRZ

Brand: Analog Devices
Analog Devices OP07DRZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

OP07DRZ — Analog & Mixed-Signal ICs | Superb Automation

OP07DRZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The OP07DRZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

OP07DRZ: 150 uV of maximum offset in an 8-lead SOIC, and why that is still useful

The OP07DRZ is a precision operational amplifier with a maximum input offset voltage of 150 uV, a maximum drift of 1.5 uV per degree C, and a noise figure of 0.25 uV peak to peak in the low frequency band. It runs from a 4 V to 18 V total supply, draws 1.1 mA, and brings a minimum common mode rejection and supply rejection of 115 dB. It is the part that turns a differential bridge or a thermocouple into something a 16-bit converter can read without an offset trim in production.

Published values

ParameterValue
Maximum input offset voltage150 uV
Input offset drift1.5 uV per C maximum
Low frequency noise0.25 uV peak to peak
Common mode and supply rejection115 dB minimum, 130 dB typical
Input bias current1 nA maximum
Supply current1.1 mA typical
Supply voltage4 V to 18 V total
Temperature range-40 C to +125 C
Package8-lead SOIC_N, also 8-lead DIP

Offset is a production cost, not only a specification

A 150 uV maximum offset means the worst part on the reel drifts the reading by an amount that is known in advance, so a production line does not need a per board offset trim. On a bridge amplifier with a 2 mV full scale, 150 uV is 7.5 percent of full scale, which is still too much to leave uncalibrated, but it is a single software offset rather than an end of line potentiometer adjustment. The 1.5 uV per degree C drift is what keeps that single calibration valid over the temperature range.

The 115 dB minimum rejection is the number that decides whether the part can be used single ended. At 115 dB a 1 V change on the common mode input moves the output by about 1.8 uV, which is small enough that a supply rail moving by a few hundred millivolts does not show up in the reading.

Noise in the band that matters

The 0.25 uV peak to peak is a low frequency figure, quoted from 0.1 Hz to 10 Hz. That is the band where a slow measurement lives, and it is the figure that competes with the converter resolution. A part with a lower wideband noise number and a worse low frequency figure will look better on a comparison table and read worse on a load cell weighing 1 g at a time.

Where the part does not fit

The supply range starts at 4 V total, so a single 3.3 V rail is outside the specification. The input common mode range stops short of the positive rail, so a high side current sense circuit needs a different part or a divided input. Both are decided before the board is laid out, not after the first article reads zero.

Sourcing notes for this family: the amplifier cross reference holds the cross references, how to verify a drop in replacement is the pre substitution check, and vendor consolidation is what we use when the part on the drawing is not on the shelf.

Two questions buyers ask

Can the OP07D run on a single 3.3 V supply? No. The minimum total supply is 4 V, so a 3.3 V rail is below the specified operating point even if the part starts on the bench.

Is the OP07D a drop in for a standard OP07? The pinout matches the industry standard 8-lead arrangement, but the offset null pins and the supply range have to be checked against the original part before a socket is reused without a board change.