Contact Us

MAX856CSA+T

Brand: Analog Devices
Analog Devices MAX856CSA+T is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

MAX856CSA+T — Analog & Mixed-Signal ICs | Superb Automation

MAX856CSA+T

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The MAX856CSA+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

MAX856CSA+T: 500 mA of Switch Current Is the Ceiling, Not the Output Current

The MAX856CSA+T is the 500 mA peak switch member of the MAX856 to MAX859 step-up converter family from Analog Devices, in the 8-pin small outline package on tape and reel. The published summary gives a 0.8 V to 6.0 V input supply, a 0.8 V typical start up voltage, 85 percent efficiency at 100 mA, 25 uA of quiescent current, a 1 uA shutdown mode, a 125 mA or 500 mA peak switch current limit depending on the member, switching up to 500 kHz, plus or minus 1.5 percent reference tolerance over temperature, a low battery detector with its own comparator input and output, and 8-pin SO or micro MAX packages. The fixed versions, the MAX856 and MAX858, select 3.3 V or 5 V at a pin, and the adjustable MAX857 and MAX859 cover 2.7 V to 6.0 V.

Peak switch current, average input current, and output power

The 500 mA figure that gives the part its reputation is a peak inductor current limit inside the switch, not a deliverable output current. With the usual 30 to 40 percent ripple, a 500 mA peak limit corresponds to an average input current around 400 mA, and the output power is that current multiplied by the input voltage and the efficiency. At a 2 V input and 85 percent, the ceiling is near 0.7 W, so 5 V at 100 mA is possible from 3 V and not possible from 1.2 V.

The arithmetic makes the point in current terms. Delivering 5 V at 100 mA from a 3.0 V input needs 196 mA of average input current at 85 percent efficiency, from 2.4 V it needs 245 mA, and from 2.0 V it needs 294 mA. From a 1.2 V input the same load would need 490 mA of average input current, which is already at the peak limit before ripple is added, so 100 mA at 5 V from a single cell is outside what this device can do. Halving the load to 50 mA brings the input current to 245 mA and the converter back inside its limits.

Two battery cells, a 3.3 V rail and the low battery detector

The part starts from 0.8 V, which is what makes it usable on two alkaline cells that are near the end of their life. Efficiency of 85 percent at 100 mA is quoted at a specific input and output, and efficiency curves fall at light load and at low input voltage, so a product that draws 5 mA most of the time should be checked on the curve rather than against the headline. The 25 uA quiescent current is 75 uW at 3 V, and 1 uA in shutdown is 3 uW, both small enough that a 1000 mAh cell is not drained by the converter between uses.

The low battery detector is a separate comparator with an input pin and an open drain output, set by a resistor divider from the input. That is a genuine cost saving in a battery product, because the alternatives are an external supervisor or an analogue input on the microcontroller with its own divider.

ParameterPublished valueWhat it decides
Input range0.8 V to 6.0 V, 0.8 V typical start upTwo alkaline cells down to end of life
Output3.3 V or 5 V pin selectable on the fixed versionsNo external divider on the fixed parts
Peak switch current500 mA on MAX856 and MAX857About 400 mA of average input current
Output ceilingNear 0.7 W from a 2 V input at 85 percent5 V at 100 mA is fine from 3 V, not from 1.2 V
Input current examples196 mA at 3 V, 245 mA at 2.4 V, 294 mA at 2.0 VWhere the switch limit starts to bind
Quiescent and shutdown25 uA, 1 uA shutdown75 uW and 3 uW at 3 V
Reference tolerancePlus or minus 1.5 percent over temperature49 mV on 3.3 V, 75 mV on 5 V
Switching frequencyUp to 500 kHzInductor size and ripple current
ExtrasLow battery comparator with input and output pinsNo separate supervisor on the board

Questions from buyers of this part number

Is the MAX858 the same part with a smaller switch? It is the 125 mA peak limit member, which is the right choice for a low current load and the wrong choice for 100 mA at 5 V. The pinout and the pin selectable output are shared, so the substitution is electrically possible and thermally limited. That is exactly the kind of substitution that works on a bench and fails at low battery.

Why does my 3.3 V rail sag when the battery is fresh? A step-up converter with a fixed output does not sag when the input rises, so a sag at high input usually means the inductor is saturating or the input capacitor is too small for the ripple current at that operating point. Both are component choices around the device, not the device.

The part is listed in the analog and mixed-signal IC category. Related buying pages are power management cross reference for the alternatives and component lead time solutions when the family is on allocation.

Request Quote — In Stock, 100% New & Original, Full Warranty