Contact Us

MAX829EUK+T

Brand: Analog Devices
Analog Devices MAX829EUK+T is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

MAX829EUK+T — Analog & Mixed-Signal ICs | Superb Automation

MAX829EUK+T

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The MAX829EUK+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

MAX829EUK+T: The 35 kHz Pump Does Not Give Lower Ripple, It Gives Smaller Capacitors

The MAX829EUK+T is the 35 kHz member of the MAX828 and MAX829 switched capacitor voltage inverter pair from Analog Devices, in the 5-pin SOT23 package on tape and reel, rated -40 C to +85 C. It takes an input from 1.5 V to 5.5 V and produces the negative of that input using two capacitors and no inductor, with a 95 percent voltage conversion efficiency, more than 90 percent power efficiency over most of the load range, and 25 mA of output current at 500 mV of drop. The four internal power MOSFET switches and the oscillator are on chip, the quiescent current is about 115 uA typical for this frequency option against 60 uA for the 12 kHz MAX828, and the data sheet pairs the 35 kHz part with 3.3 uF flying and reservoir capacitors where the MAX828 is specified with 10 uF.

Output resistance is set by the pump frequency times the flying capacitor

The charge pump is not a regulator. Its output resistance is roughly 1 divided by the product of the oscillator frequency and the flying capacitor, plus twice the switch resistance and the capacitor ESR. At 35 kHz with 3.3 uF that first term is 8.66 ohm, and with the internal switch resistance of about 8.5 to 9 ohm and two low ESR capacitors the total lands near 26 ohm. At 25 mA that is a 0.65 V drop, which is why the published figure is 25 mA at 500 mV and why the datasheet's own 20 ohm typical is quoted at 5 V in with a light load.

The same arithmetic explains the MAX828: 12 kHz with 10 uF gives 8.33 ohm for the first term, so the two parts end up with almost the same output resistance, 25.5 ohm against 25.9 ohm. The 35 kHz version is not a lower impedance part. It reaches the same impedance with a third of the capacitance, which is the actual reason to pay for it: 3.3 uF ceramics are smaller and cheaper than 10 uF ceramics, and the board area saved is the reason to take it.

Ripple follows the same product, so the faster part is not quieter

Peak to peak ripple is the load current divided by the product of frequency and reservoir capacitor, plus twice the load current times the capacitor ESR. At 25 mA, 35 kHz and 3.3 uF that is 216 mV, and the MAX828 at 12 kHz and 10 uF gives 208 mV. The two are within four percent of each other, which is the honest answer to the question buyers ask most often about this family: a higher pump frequency does not reduce ripple unless the reservoir capacitor is increased at the same time. Going to 10 uF on the MAX829 would cut ripple to 71 mV, and that is a capacitor decision, not a part number decision.

What the 115 uA quiescent current costs at light load

Efficiency at 25 mA with a 5 V input and a 4.5 V output works out at 89.6 percent, essentially the same as the MAX828, because at that load the quiescent current is a fraction of a percent of the output. At a 1 mA load the 115 uA is 11.5 percent of the load, so the same converter returns about 78 percent, and at 100 uA the pump's own standing current is larger than the load. A -5 V bias rail that only feeds an op-amp quiescent current belongs on the 60 uA part, and a -5 V rail that feeds a 20 mA LCD bias belongs on either.

ParameterPublished valueWhat it decides
Input range1.5 V to 5.5 VRuns from a single lithium cell or a 5 V bus
OutputNegative of the input, 25 mA at 500 mVNot a regulated rail, it droops with load
Pump frequency35 kHz for the MAX829, 12 kHz for the MAX828Four times higher frequency, one third the capacitance
Capacitors3.3 uF flying and reservoir in the 35 kHz specificationSmaller footprint than the 10 uF pairing
Output resistanceAbout 26 ohm computed, 20 ohm typical at light load0.65 V droop at 25 mA
Ripple at 25 mA216 mV computed from the published equationSame as the 12 kHz part with 10 uF
Quiescent currentAbout 115 uA typical11.5 percent of a 1 mA load
Output current limit50 mA absolute maximum on OUTTwo devices in parallel for more

Questions buyers ask before they order this part number

Can two MAX829EUK+T devices be paralleled for more current? Yes, and the data sheet shows the arrangement: each device keeps its own flying capacitor and they share one reservoir capacitor, whose value is increased by the number of devices. Output resistance falls in proportion to the count, so two parts give about 13 ohm and 50 mA total at the same 0.65 V droop. The sum of the output currents still has to respect the 50 mA absolute maximum per device.

What happens if the load pulls OUT above ground? The part has no protection against current being forced into OUT from an external source, and the data sheet calls for a Schottky diode between ground and OUT, anode on OUT, in any application where a heavy load can source current back. That is the same precaution a negative rail needs when a second supply comes up first, and it is a board level part of the specification rather than an optional extra.

The part is listed in the analog and mixed-signal IC category. Buyers comparing charge pump options use power management cross reference, and programmes that need a second source for a bias rail start from component lead time solutions.

Request Quote — In Stock, 100% New & Original, Full Warranty