MAX828EUK+T
Product Specifications
MAX828EUK+T
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The MAX828EUK+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
MAX828EUK+T: 60 uA of Quiescent Current and Where It Stops Being Free
The MAX828EUK+T is the 12 kHz member of the MAX828 and MAX829 switched capacitor inverter pair from Analog Devices, in the 5-pin SOT23 package on tape and reel, rated -40 C to +85 C. It inverts an input between 1.5 V and 5.5 V with two capacitors and no inductor, delivers 25 mA with 500 mV of drop, reaches a 95 percent voltage conversion efficiency and more than 90 percent power efficiency over most of the load range, and draws 60 uA of quiescent current. The data sheet specifies it with 10 uF flying and reservoir capacitors, quotes an output source resistance of about 20 ohm at room temperature on a 5 V input, and allows 50 mA absolute maximum on the output. A combined doubler and inverter circuit is also shown, with a 40 mA limit on the sum of the two output currents.
The 20 ohm figure is a light load number, and the resistance is built from three parts
Output resistance is the sum of an ideal switched capacitor term, 1 divided by frequency times the flying capacitor, plus twice the internal switch resistance and the two capacitor ESR values. At 12 kHz with 10 uF the first term is 8.33 ohm, and with switch resistance near 8.5 ohm the total comes to about 25.5 ohm, not 20 ohm. The 20 ohm figure in the data sheet is measured at 5 V input and a light load, and it is the number buyers quote back when a 25 mA load droops further than expected: 25 mA through 25.5 ohm is 0.64 V, which on a 5 V input leaves -4.36 V rather than the -4.75 V a quick reading of the specification suggests.
The way to buy margin is the capacitor. Doubling the flying capacitor to 20 uF takes the first term to 4.17 ohm and the total to 21.3 ohm, at the cost of one larger ceramic. Doubling both the flying and the reservoir capacitor also halves the ripple, which is the second thing a negative bias rail usually needs.
Quiescent current is negligible at 25 mA and dominant at 100 uA
At 25 mA out of a 5 V input with a 4.5 V output, the 60 uA adds 0.24 percent to the input current and the efficiency works out at 89.8 percent. At 1 mA it is 6 percent of the load and the efficiency falls to about 94 percent of the ideal ratio, and at 100 uA the converter's own standing current is 60 percent of the delivered current, so the efficiency drops to roughly 62 percent. A -5 V rail that powers an op-amp quiescent budget is therefore spending most of its input power in the pump itself, and at that point a resistor divider or a small charge pump with shutdown is the cheaper engineering answer.
The part has no shutdown pin. The data sheet points to the MAX1719, MAX1720 and MAX1721 for logic controlled shutdown and shows a discrete circuit that switches the input pin if the function is needed on this part number. A buyer who assumes every SOT23 charge pump can be turned off will find that this one cannot.
Paralleling, cascading and the direction current is allowed to flow
Two devices in parallel each keep their own flying capacitor and share one reservoir capacitor sized for the pair. Output resistance halves to about 12.8 ohm, so 50 mA total produces the same 0.64 V droop that one device produces at 25 mA. Cascading two devices in series doubles the magnitude to -2 times the input, and the second stage sees the first stage's droop, so the output is not exactly twice the input under load. For heavy loads that can force current into OUT, a Schottky diode from OUT to ground with the anode on OUT is required, and the data sheet names the 1N5817.
| Parameter | Published value | What it decides |
|---|---|---|
| Input range | 1.5 V to 5.5 V | Single cell or 5 V bus, no inductor |
| Output | Negative input, 25 mA at 500 mV drop | Droop is load times output resistance |
| Output resistance | 20 ohm typical at light load, about 25.5 ohm computed at 25 mA | 0.64 V droop at full load |
| Capacitors | 10 uF flying and reservoir in the specification | Doubling them halves the first resistance term |
| Quiescent current | 60 uA | 6 percent of a 1 mA load, 60 percent of a 100 uA load |
| Efficiency | Above 90 percent over most of the range | 89.8 percent at 25 mA, about 62 percent at 100 uA |
| Shutdown | None on this part number | MAX1719 and MAX1720 add it |
| Output absolute maximum | 50 mA | Two in parallel for 50 mA total |
Questions buyers ask before they order this part number
Is the MAX828 a regulated negative supply? No. The output approaches the negative of the input only at light load and falls toward ground as current rises, following the output resistance curve. A circuit that needs a fixed -5 V at any load needs a regulated inverter or a linear post regulator after this part, and a circuit that needs a negative bias at a few milliamps can use the pump on its own.
Does the 12 kHz version have any advantage over the 35 kHz MAX829? Lower quiescent current, 60 uA against about 115 uA, and lower switching noise in the audio band because the pump runs below it. The cost is that the same output resistance needs a 10 uF flying capacitor instead of 3.3 uF, so the choice is between board area and standing current, and a battery product that sleeps at microamps takes the 12 kHz part.
The part sits in the analog and mixed-signal IC category. Buyers comparing charge pumps open power management cross reference, and boards that are re-costing a bias rail start from how to reduce component cost.
Request Quote — In Stock, 100% New & Original, Full Warranty