LTM8074IY#PBF
Product Specifications
LTM8074IY#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM8074IY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM8074IY: 1.2 A in a 4 mm square, and where the 48.9 degree thermal path bites
The LTM8074IY#PBF is the smallest module in the 40 V Silent Switcher family: 4 mm by 4 mm by 1.82 mm, 1.2 A continuous and 1.75 A peak, 0.8 V to 12 V out from 3.2 V to 40 V in, switching from 200 kHz to 2.2 MHz. The low profile matters as much as the footprint, because 1.82 mm allows the part to sit on the underside of a board under a connector or a display. The price of that size is a junction to ambient resistance of 48.9 degrees per watt, the highest in the family, which puts the thermal arithmetic in front of the current rating rather than behind it.
Published values
| Parameter | Value |
|---|---|
| Input range | 3.2 V to 40 V, minimum input at 3.2 V on a rising supply |
| Output range | 0.8 V to 12 V, 0.8 V with the feedback pin open |
| Continuous current | 1.2 A |
| Peak current | 1.75 A at 3.3 V out and 1 MHz |
| Switching frequency | 200 kHz to 2.2 MHz; RT of 221k, 40.2k and 16.2k for the three points |
| Feedback voltage | 774 mV typical, 760 mV to 786 mV over temperature |
| Line and load regulation | 0.5 percent and 0.5 percent |
| Output ripple | 15 mV at 1.2 A |
| Shutdown current | 3 microamps into VIN with RUN at 0 V |
| No load current | 8 microamps not switching with SYNC at 0 V |
| Power good window | 0.84 V falling and 0.70 V rising against a 774 mV reference |
| RUN thresholds | 1.2 V rising, 0.9 V falling, plus or minus 50 nA of pin current |
| Package | BGA, 4 mm by 4 mm by 1.82 mm, 0.08 g, MSL 3 |
| Thermal | 48.9 degrees per watt junction to ambient, 17.2 to the board, 33.4 to the top |
| Temperature grade | -40 to +125 degrees internal |
| Special | configurable as an inverting converter for a negative rail |
What 48.9 degrees per watt allows at 85 degrees ambient
Forty degrees of junction headroom divided by 48.9 degrees per watt is 0.82 W of dissipation. At 3.3 V and 1.2 A, which is 3.96 W out, that is an efficiency floor of 82.9 percent and the module clears it with room. At 5 V and 1.2 A, 6 W out, the floor is 88 percent. At 12 V and 1.2 A, 14.4 W out, the floor is 94.6 percent, which is at or past the edge of what a 40 V input can do at 2.2 MHz.
So the honest statement of this part is that 1.2 A is available at the low end of the output range in still air, and at 12 V out the same current needs either a lower ambient or airflow. The peak rating of 1.75 A behaves the same way: it is a transient number, sized for a load step, not for a continuous rail.
Frequency is the lever, not the current limit
The 200 kHz to 2.2 MHz span lets the same module be quiet or small. Low frequency gives the best efficiency and the worst ripple, high frequency gives a 4 mm part that still passes conducted emissions with small ceramics, and the data sheet shows the trade at each output voltage. A 2.2 MHz setting also keeps the switching harmonic clear of the 150 kHz to 30 MHz conducted band's worst region for some receivers, which is sometimes the reason the part was chosen in the first place.
The single resistor on RT sets it, and the value is a hard number, not an approximation: 221k for 200 kHz, 40.2k for 1 MHz, 16.2k for 2.2 MHz. Changing it after the board is built means re-checking the inductor ripple and the output capacitor, because both were sized for the original point.
The inverting configuration and the industrial grade
The module can be wired as an inverting converter, which turns a positive input into a negative rail without a second part number. That is useful for amplifier supplies in instrumentation, where a -5 V or -12 V rail has to track the positive one. The catch is that the feedback and RUN pins now reference the negative output, so the enable logic has to be level shifted, and the input current rises by the ratio of the two rails.
The I grade guarantees the whole table from -40 degrees, which is what an instrument that ships to a plant without heating needs. The same board in a bench product could use the E grade, since both share the 774 mV reference and the same pin out.
Buyers usually arrive at the power management cross reference to find the family alternatives, then use OEM procurement to confirm a substitute before it is fitted; component lead time solutions is the routine for a part that has already stopped shipping.
Two questions buyers ask about the 4 mm part
Why is the feedback 774 mV rather than 800 mV? It is the reference this die was trimmed to, and it is not interchangeable with the 800 mV used on the larger members of the family. A divider copied from an LTM8078 builds a rail 3.4 percent high on this part. Recompute the divider from 774 mV.
Can it deliver 1.2 A at 12 V out from 24 V in? The current is available, but at 85 degrees ambient the thermal budget requires 94.6 percent efficiency to hold a 125 degree junction, so the honest answer is not in still air. Check the derating curve for the specific input, output and airflow before promising the rail.