LTM8055IY#PBF
Product Specifications
LTM8055IY#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM8055IY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM8055IY: 36 V buck-boost for industrial buses that sag and surge
The LTM8055IY#PBF is the industrial grade of the 36 V buck-boost module, 8.5 A at 12 V out from 24 V in, 1.2 V to 36 V out with the output allowed above, equal to or below the input, in a 15 mm square package with a 20.5 degrees per watt thermal path. The guarantee covers -40 to +125 degrees internal by test. The reason this part exists is the 24 V industrial bus, which sits at 24 V nominal, sags to 18 V on a contactor drop and surges to 30 V on a load dump, and needs a 12 V rail that does not care.
Published values
| Parameter | Value |
|---|---|
| Input range | 5 V to 36 V |
| Output range | 1.2 V to 36 V, any relationship to the input |
| Output current | 3 A at 6 V in and 12 V out; 8.5 A at 24 V in and 12 V out |
| Efficiency | up to 97.5 percent in buck mode |
| Switching frequency | 100 kHz to 800 kHz |
| Feedback voltage | 1.2 V nominal, 1.176 V to 1.220 V over temperature |
| Input current limit | 56 mV sense threshold, adjustable |
| Output current limit | 61.5 mV sense threshold, adjustable |
| Current monitors | IINMON and IOUTMON, 1.04 V and 1.26 V at the limits |
| Quiescent current | 0.1 microamp typical with RUN low |
| No load current | 8 mA discontinuous, 45 mA forced continuous |
| Package | 121 lead BGA, 15 mm by 15 mm by 4.92 mm |
| Thermal | 20.5 degrees per watt to ambient |
| Temperature grade | -40 to +125 degrees internal, guaranteed by test |
The 18 V sag is the case that decides the part
A 12 V rail from a 24 V bus is a buck at nominal. At 18 V in it is still a buck, but at 12 V in it is a pass-through and below that it is a boost. A plain buck drops out somewhere around 13 V and the rail follows the bus down, which resets every downstream converter. The buck-boost holds 12 V all the way to the 5 V input floor.
That is worth a 15 mm package only if the load matters during the sag. For a controller that has to ride through a contactor drop and keep its state, it does. For a heater or a lamp, a buck plus a big capacitor is cheaper.
Current limits sized for a real bus
The input sense threshold of 56 mV with a 5 milliohm shunt gives 11.2 A, which is above the 8.5 A output rating at 12 V because the input current is lower in buck mode. Set the limit from the source's capability, not from the converter's rating: a 24 V bus fused at 10 A wants the limit below the fuse, and the control pin gives a continuous range to do that.
The output limit protects a load that could otherwise pull the rail into current limit, such as a stalled motor or a cold filament. Because the module can boost, an output short does not simply collapse the rail, it makes the input current rise, which is why the input limit is the more important of the two on a shared bus.
Thermals on a 15 mm package
The 11 degrees per watt junction to board means most of the heat leaves through the pads, so the copper under the part is part of the rating. A board with a solid plane and thermal vias gets close to the published number; a two layer board with a broken plane loses most of the advantage and the module derates.
At 70 degrees ambient and 2.6 W of loss the junction sits at 123 degrees, right at the limit, which is the arithmetic behind the statement that 8.5 A is not an 85 degree number. A fan or a metal chassis that touches the board is what turns the headline into a continuous rating.
Sourcing notes for this family: the power management cross reference holds the cross references, OEM procurement is the pre substitution check, and component lead time solutions is what we use when the part on the drawing is not on the shelf.
Two questions buyers ask about the industrial buck-boost
Does the module need an external inductor? No. The inductor, the four switches and the controller are inside the package. External parts are the input and output capacitors, the feedback divider, the frequency resistor and the sense resistors if the current limits are used.
Can the output be higher than 36 V? No, 36 V is both the input and the output ceiling, and the part is a buck-boost rather than a boost, so a 48 V output is outside the family. A 36 V output from a 24 V input is the top of the usable range.