LTM8054IY#PBF
Product Specifications
LTM8054IY#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM8054IY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM8054IY: the 5.4 A buck-boost for a 24 V industrial bus
The LTM8054IY#PBF is the industrial grade of the 36 V, 5.4 A buck-boost module in the 3.42 mm tall 11.25 mm by 15 mm package. It holds a 1.2 V to 36 V output with the input above, equal to or below it, and it is guaranteed over -40 to +125 degrees internal by test, which is the specification most industrial equipment actually claims. The 17.6 degrees per watt junction to ambient path is the lowest in the buck-boost family, and the adjustable input and output current limits are the reason it appears on battery and motor supplies as often as on plain rails.
Published values
| Parameter | Value |
|---|---|
| Input range | 5 V to 36 V |
| Output range | 1.2 V to 36 V |
| Output current | 1.8 A at 6 V in; 3.4 A at 12 V in; 5.4 A at 24 V in, all at 12 V out |
| Efficiency | up to 94 percent |
| Switching frequency | 100 kHz to 800 kHz, synchronisable from 200 kHz to 700 kHz |
| Feedback voltage | 1.2 V nominal, 1.176 V to 1.220 V over temperature |
| Current limits | input 56 mV sense threshold, output 61.5 mV, both adjustable |
| Quiescent current | 0.1 microamp typical with RUN low |
| No load current | 8 mA discontinuous, 45 mA forced continuous |
| Package | BGA, 11.25 mm by 15 mm by 3.42 mm |
| Thermal | 17.6 degrees per watt to ambient |
| Temperature grade | -40 to +125 degrees internal, guaranteed by test |
| Finish | SAC305 RoHS, tin lead under the same device code |
Sizing the current limits from the fuse, not the module
A 56 mV input sense threshold with a 5 milliohm shunt is 11.2 A, which is far above a 5.4 A output at 12 V in buck mode. That is a protection level, not an operating point, and it is meant to be brought down with the control pin until the input limit sits below the fuse or the connector rating.
The reason to bother is that a buck-boost with a 5 V input floor will happily draw a large input current in boost mode, and a fault on the output turns into an input current event rather than an output voltage collapse. The input limit is the only thing that stops it.
What the 1.2 V reference costs in divider tolerance
The reference is 1.2 V with plus or minus 1 percent at 25 degrees and 1.176 V to 1.220 V over temperature, which is plus or minus 1.8 percent. On a 12 V rail that is 216 mV, larger than the 0.5 percent line and load regulation terms. A precision rail therefore needs either a trim or a converter with a tighter reference, because the divider and the reference set the absolute accuracy and the loop only holds the relative one.
Use 0.1 percent resistors if the rail has to be within 1 percent, and remember that the divider current flows continuously: a 100 k upper and 10.9 k lower at 12 V draws about 108 microamps, which is significant against a 0.1 microamp shutdown current if the rail is expected to be off.
Where this part is the right size
Twenty four volts in, 12 V out at 5.4 A is 65 W, which covers a motor drive's logic supply, a bank of sensors, or a charging rail for a small battery. Above that, the 8.5 A module is the same die family in a taller package with a lower current density per square millimetre.
Below 2 A a buck converter is enough and the buck-boost is buying a capability the load does not use. The decision point is whether the rail must survive the bus falling below the output voltage, and that is a question about the system, not about the converter.
Where a customer needs a second position on this part, the power management cross reference is the starting point, OEM procurement sets out the checks a substitution has to pass, and BOM shortage recovery is the short lead time route we quote against.
Two questions buyers ask about this module
Is the pin out the same as the 8.5 A part? No. The packages are different sizes, 11.25 mm by 15 mm by 3.42 mm against 15 mm by 15 mm by 4.92 mm, with different ball maps. They are not interchangeable on an existing board.
Does it need an external compensation network? No. The LTM8054 is internally compensated. The LTM8055-1 is the member of the family that brings compensation out to pins for loads outside the standard range.