LTM8052IV#PBF
Product Specifications
LTM8052IV#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM8052IV#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM8052IV: the 5 A two-quadrant module where the sink limit is the larger number
The LTM8052IV#PBF is a 36 V input, 5 A constant-voltage constant-current step-down module that both sources and sinks output current. The controller, the power switches, the inductor and the support parts sit inside an 11.25 mm by 15 mm by 2.82 mm land grid array that weighs 1.4 g, so a rail that has to hold its setpoint while the load pushes current back needs no external power stage. The output voltage is set by one resistor from ADJ, the current limit by an analogue voltage on CTL_I, and a second control pin, CTL_T, is intended for a thermistor network that walks the limit down as the board heats up. Switching runs from 100 kHz to 1 MHz and the part is forced continuous, so it never skips cycles near no load.
Published values
| Parameter | Value |
|---|---|
| Input range | 6 V to 36 V, 40 V absolute maximum on VIN |
| Output range | 1.2 V with ADJ open to 24 V with a 499 ohm resistor |
| Output current | plus or minus 5 A with CTL_I and CTL_T at 1.5 V; 6 A is the absolute maximum rating |
| Positive current limit | 5.6 A typical at 1.5 V, 5.1 A to 6.1 A over the parts; 2.8 A typical at 0.75 V |
| Negative current limit | 7.7 A typical at 1.5 V, 6.9 A to 8.5 A over the parts; about 2 A larger than the source side |
| ADJ pin | 1.19 V nominal, 1.16 V to 1.22 V; 100 microamps flows out of the pin |
| Reference output | 2.00 V at 0.5 mA, 1.93 V to 2.04 V |
| Switching frequency | 1 MHz with RT at 40.2k, 100 kHz with RT at 453k |
| Quiescent current | 17 mA typical, 30 mA maximum at no load; 0.1 microamps in shutdown |
| Line and load regulation | 0.1 percent and 0.7 percent |
| Output ripple | 10 mV RMS at 4.5 A |
| Thermal | 18.6 degrees per watt junction to ambient, 5.4 to the board, 10.8 to the top |
| Package | 81 lead LGA, 15 mm by 11.25 mm by 2.82 mm, MSL 3, 1.4 g |
| Temperature | module limits guaranteed over the full -40 to +125 degree internal range |
The sink side has roughly two amps more room than the source side
The current loop is not symmetric. At a control voltage of 1.5 V the source limit is 5.6 A typical, but the sink limit is 7.7 A typical, an offset of about 2 A that the data sheet calls out and that the transfer curves show. On a Peltier driver this matters in both directions: the cold side and the hot side of a module do not draw the same current, and a rail sized on 5 A will still hold regulation when the device swings the other way at 6 or 7 A.
What the extra sink current buys is headroom for regenerative load steps, not a licence to run the part at 7 A in reverse forever. The limit is a current limit, so above it the output starts to rise, and once it passes 125 percent of the setpoint the overvoltage lockout stops switching. The energy is not dissipated in the module, it is pushed back into the input bus, which is the next point to plan for.
Sinking current raises the input, not the package temperature
The module regulates a sinking load by power conversion, so the current it absorbs is delivered to its own input. Without something on that bus to take the energy, the input voltage climbs, and VIN is rated 40 V against a 36 V operating ceiling. A battery charger test rig, a supercap bank and a motor drive all put energy back at some point in the cycle, so the input needs a clamp, a dump load or a battery that can accept the charge.
The second limit is the internal power diode. If the output is driven above the input, that diode conducts and the output is clamped a diode drop above VIN, and current regulation is lost. A 24 V rail fed from a 12 V bus will therefore sit at 12 V plus a drop with no regulation at all, which is the failure that reads as a dead module on the bench and is really a topology question.
Thermal arithmetic at 5 A, and where the rating stops being honest
At an 85 degree ambient the junction has 40 degrees of headroom to the 125 degree limit, which through 18.6 degrees per watt is 2.15 W of dissipation. Five amps at 2.5 V is 12.5 W out, so the rail has to run at 85.3 percent efficiency to hold the rating in still air, which a 12 V to 2.5 V conversion of this size does. Five amps at 5 V is 25 W out and needs 92.1 percent, and five amps at 12 V is 60 W out and needs 96.5 percent, which is past what the family delivers.
The honest statement is that 5 A is available at the low end of the output range and at 5 V in a ventilated enclosure, and that the same current at 12 V or 24 V out has to be checked against the derating curves for the actual input, output and airflow. The 6 A absolute maximum on output current is a stress rating, not a continuous figure, and no thermal number above applies to it.
For a board that has to keep running while a reel runs out, the power management cross reference is where the family alternatives sit, OEM procurement is the check list before a substitute goes in, and component lead time solutions is how a gap is covered without a new line item.
Two questions buyers ask about this rail
Can this charge a battery at constant current and then hold constant voltage? Yes, that is the CVCC function. Set the top voltage with the ADJ divider and the charge current with a resistor or a control voltage on CTL_I, and the loop holds current until the battery reaches the setpoint and then holds voltage. Put a thermistor network on CTL_T so the limit falls as the cell warms up.
What sets the output voltage exactly? One resistor from ADJ to ground, into the equation 1.19 V times one plus 10 k divided by RADJ. The ADJ window is 1.16 V to 1.22 V, so a 5 V rail built from the typical value can land 2.5 percent off before the resistor tolerance is counted.