Contact Us

LTM8025EY#PBF

Brand: Analog Devices
Analog Devices LTM8025EY#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8025EY#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8025EY#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8025EY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8025EY#PBF: a 0.8 V rail from a 36 V bus and the duty cycle that follows

The LTM8025EY#PBF is the E grade of the 36 V, 3 A module in the 9 mm by 15 mm by 4.92 mm ball grid array with SAC305 balls and MSL 3. It covers 3.6 V to 36 V in and 0.8 V to 24 V out, with the output set by a resistor to the ADJ pin, which the module regulates to 790 mV, so an open ADJ pin gives 0.8 V. The E grade is -40 C to 125 C at the junction and the frequency range is 200 kHz to 2.4 MHz.

Published values

ParameterValue
Input voltage3.6 V to 36 V
Output voltage0.8 V with ADJ open, up to 24 V with a resistor
ADJ reference790 mV typical, 775 mV to 805 mV over temperature
ADJ pin current2 uA out of the pin
Output current3 A
Duty cycle at 0.8 V from 36 V2.2 percent
On time at 400 kHz55.6 ns
On time at 1.8 MHz12.3 ns
Junction to ambient24.4 C/W
Temperature range-40 C to 125 C, E grade

A 2.2 percent duty cycle is where the module stops

At 36 V in and 0.8 V out the high side switch is on for 2.2 percent of the period. At 400 kHz with a 100 k resistor that is 55.6 ns, and at 1.8 MHz with 14.7 k it is 12.3 ns. Propagation delay, gate drive and current sense blanking all live inside that window, so the top of the frequency range is not available at the bottom of the output range.

The practical ceiling for a 0.8 V rail from 36 V is therefore around 400 kHz to 600 kHz, and a specification that asks for 2 MHz on that rail is asking for a frequency the part cannot hold. At 12 V in the same 0.8 V output is a 6.7 percent duty cycle and the whole frequency range opens up, which is why a two stage conversion is often the honest answer for a 36 V bus.

The reference tolerance and a 0.8 V rail

The ADJ pin is regulated to 790 mV with a window of 775 mV to 805 mV over temperature, which is plus or minus 1.9 percent around the typical value. The ADJ pin also sources 2 uA, which through a 16.9 k resistor is 34 mV, so the pin current is part of the arithmetic on any output above a few volts and is negligible at 0.8 V.

For a 0.8 V rail feeding a processor core, the total window has to include the module's own regulation, the resistor tolerance and the load's tolerance, and the module's 790 mV reference is already 2 percent of it. That is why core rails in this class are usually trimmed at test rather than left to the resistor.

What 3 A at 0.8 V looks like thermally

0.8 V at 3 A is 2.4 W out and about 0.6 W of loss at 80 percent, which on 24.4 C/W is a 15 C rise. The low output is thermally free and electrically constrained, which is the opposite of the 12 V rail in the same package where 36 W out means a 66 C rise.

The input current is 0.083 A at 36 V for that load, so the input capacitor is small and the input ripple is negligible. A board that carries both a 0.8 V core rail and a 12 V rail from the same 36 V bus has two modules with very different thermal stories in the same footprint, and the copper should be apportioned accordingly.

E grade and the burst mode trade

The E code is -40 C to 125 C, the same as the I code, and 15 C short of the MP codes at the cold end. For a commercial or industrial board this is the grade that gets bought, and the difference against the I code is a documentation question rather than a performance one.

At light load the module enters burst mode and the input current falls to about 50 uA. A 0.8 V core rail that spends most of its life in standby is a good candidate for that behaviour, and a rail that feeds an ADC reference is not, because the burst ripple appears on the output.

Where a customer needs a second position on this part, the power management cross reference is the starting point, how to verify a drop in replacement sets out the checks a substitution has to pass, and one stop BOM sourcing is the short lead time route we quote against.

Two questions buyers ask

Can the 0.8 V output run at 2.4 MHz? Practically no. A 2.2 percent duty cycle at 2.4 MHz is 9.3 ns of on time, which the module cannot hold. Around 400 kHz to 600 kHz is the usable range for that output from a 36 V bus.

What does an open ADJ pin give? 0.8 V. The pin is regulated to 790 mV typical and the output follows the divider from that reference, so an open pin is the minimum setting rather than an undefined state.