Contact Us

LTM8023IV#PBF

Brand: Analog Devices
Analog Devices LTM8023IV#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8023IV#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8023IV#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8023IV#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8023IV#PBF: Industrial Grade, Land Grid Array, and the 2.82 mm Height That Comes With It

The LTM8023IV#PBF is the industrial grade of the 2 A, 36 V step-down module in the land grid array body, 9 mm by 11.25 mm by 2.82 mm, specified over minus 40 to plus 85 degrees. Inside the package are the controller, the power switches, the inductor and the compensation, so the external component list is bulk input and output capacitors plus two resistors: one setting the output voltage from the 0.79 V feedback threshold and one setting the switching frequency between 200 kHz and 2.4 MHz. The 2.82 mm height is 0.6 mm lower than the ball grid array version of the same module, which is the reason this code exists as a separate order number.

Height, pads and the inspection question

A land grid array has flat pads on the bottom of the body and no balls, so after reflow the joints are visible from the side and an optical inspection machine can confirm that the solder has wetted and formed a fillet. That is a production advantage, not an electrical one, and it is the reason a line that inspects optically will standardise on the LGA code even when the BGA code costs the same. The lower profile also helps in an enclosure where the module sits under a heatsink or a card guide, and it reduces the thermal resistance to a heatsink that is pressed onto the top of the package, because there is less material between the die and the surface.

Input, output and the two resistors that set everything

The input range is 3.6 V to 36 V and the output range is 0.8 V to 10 V, with the output voltage set by RADJ equals 394.21 divided by the output voltage minus 0.79, in kilo ohms. A 5 V output is about 93.6 kohm, a 3.3 V output about 157 kohm and a 2.5 V output about 230 kohm. The frequency resistor on the RT pin sets the switching frequency and the data sheet gives a recommended value for each input and output pair, which is not optional: the internal inductor is fixed, and a frequency far from the recommendation changes the ripple current beyond what the output capacitor was chosen for. Soft start is a capacitor on the RUN/SS pin, and the pin also has to be above 2.5 V for normal operation, which is a detail that catches systems that drive it from a slow rising rail.

ParameterValue on this order codeWhat it decides
PackageLGA, 9 mm by 11.25 mm by 2.82 mmLower than the BGA code, pads inspectable
Temperature gradeI, minus 40 to plus 85 degreesFully specified across the range
Input range3.6 V to 36 VRunning range, start-up needs more
Output0.8 V to 10 V at 2 ASet by one resistor to ground
Feedback threshold0.79 VOutput below 0.79 V is not reachable
Frequency200 kHz to 2.4 MHzRecommended value follows input and output
RUN/SSAbove 2.5 V for normal operationSoft start is a capacitor on the same pin
Moisture sensitivityMSL 3Dry pack handling applies before reflow
FinishGold pads, RoHSPad finish is e4 on this code

Efficiency and where the loss sits

At 12 V in and 3.3 V out the module runs in the high 80s percent across most of its load range, and at 36 V in the same output current the loss rises because the switching loss scales with the input voltage. The practical consequence is that a 2 A load at 36 V in has to be checked against the derating curves for the actual board, while the same 2 A at 12 V in is comfortable. The internal inductor is the part that sets the ripple, so the output capacitor value is chosen for the ripple at the recommended frequency and not for the lowest frequency that will work at light load.

Where the code belongs

Industrial equipment that needs a low profile point of load converter from a 12 V or 24 V rail and an optical inspection step at the end of the line is where this order code is the right answer. Where the ambient can exceed plus 85 degrees the MP grade is the specified part, and where the line X-rays its arrays the BGA code is equally good. The pin to pin cross reference covers the LGA and BGA bodies, the ADI part second source page lists the fields a substitute module has to match, and the one stop BOM sourcing page covers the module with the capacitors and resistors it needs.