Contact Us

LTM8020EV#PBF

Brand: Analog Devices
Analog Devices LTM8020EV#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8020EV#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8020EV#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8020EV#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8020EV#PBF: the 6.5 V start-up floor behind a 4 V input specification

The LTM8020EV#PBF is the E grade of the 200 mA, 36 V step-down module in the 6.25 mm by 6.25 mm by 2.32 mm land grid array. The specification says the input range is 4 V to 36 V and the front page application says 6.5 V to 36 V, and the gap between those two numbers is the part of the data sheet most often missed: 4 V is where the regulator will still run, 6.5 V is where it holds a 5 V output with margin. A board fed from a 5 V rail at minus five percent is at 4.75 V and is in that gap.

Published values

ParameterValue
Input voltage4 V to 36 V, 40 V absolute maximum
Output voltage1.25 V to 5 V, 5 V typical application from 6.5 V in
Output current200 mA continuous
Output set resistor165 k for 5 V, 301 k for 3.3 V
Input capacitance2.2 uF ceramic
Output capacitance4.7 uF to 10 uF ceramic
Radiated emissionsEN55022 Class B compliant
BIAS pin3 V to 25 V, improves efficiency when a higher rail is available
Thermal resistance23.1 degree C per W
Maximum junction temperature125 degree C
E grade rangeminus 40 degree C to 85 degree C
Package21-lead LGA, 2.32 mm height

What the 2.5 V gap between 4 V and 6.5 V is for

A step-down regulator has a maximum duty cycle, and at that limit the output is the input minus the drop across the switch and the inductor. To hold 5 V from a 5 V rail the part would have to run at 100 percent duty, which it cannot, so the vendor prints 6.5 V as the input where a 5 V output is guaranteed with margin. The 4 V figure in the specification belongs to the parts of the range where the output is set below the input by the expected headroom.

Practical case: a 5 V backplane at minus five percent is 4.75 V, and a 5 V output from that rail is outside the guaranteed region. The same board with a 3.3 V output from the same 4.75 V rail has 1.45 V of headroom and is comfortable. This is the single most common mismatch on this part, and it is visible only by reading the typical application note under the circuit diagram.

The BIAS pin is worth a wire when a higher rail exists

The package has a separate BIAS pin that can be powered from 3 V to 25 V, and the data sheet asks for it when a higher rail is available because the internal circuitry then draws from that rail instead of from the input. On a 36 V input the saving is small in absolute terms but it moves the internal loss out of the input path, which is where the 40 V absolute maximum lives. On a 5 V input there is nothing to gain and the pin is tied to the input or left open as the application shows.

The bias rail also sets a limit: the absolute maximum for VIN plus BIAS together is 47 V, so a 36 V input with a 12 V bias already uses 48 V and is over the limit. A 36 V rail therefore runs with the BIAS pin tied to the input or to a rail at or below 11 V.

Where 200 mA and EN55022 Class B come from in the same package

The radiated emissions claim is what the package is arranged around: the inductor is inside, the switch node is short, and the loop area is fixed by the land pattern rather than by the user. That is the reason a 6.25 mm module can claim Class B radiated without a shield, and it is also the reason the input capacitor has to be placed against the pins: the loop that is small inside the package becomes large again through a 10 mm trace to a capacitor.

Conducted emissions are a separate test and the data sheet says they need standard filter components, so a build that has to pass both has an input filter to add even though the radiated side is already met. For a 200 mA rail the filter is small, but it has to be there before the compliance run rather than after it.

For a board that has to keep running while a reel runs out, the power management cross reference is where the family alternatives sit, one stop BOM sourcing is the check list before a substitute goes in, and component lead time solutions is how a gap is covered without a new line item.

Two questions buyers ask

Can the output be taken below 1.25 V? Not without an external offset. The 1.228 V to 1.265 V reference at the ADJ pin is the bottom of the adjustment range, so 1.25 V is the lowest output the resistor alone can set. A 1.0 V rail needs either a different module in the family with a lower reference or an amplifier that adds an offset into the feedback node, and the second option costs more accuracy than it saves.

What happens at light load? The part runs in Burst Mode at light load, so the switching frequency falls with the load and the output ripple becomes a series of bursts rather than a continuous waveform. On a 200 mA rail feeding a radio or a converter that is sensitive to a 20 mV burst, the fix is a larger output capacitor or a small preload, not a different module: the same behaviour appears on every member of this family and it is what makes the quiescent current low enough for a battery product.