Contact Us

LTM8001IY#PBF

Brand: Analog Devices
Analog Devices LTM8001IY#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8001IY#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8001IY#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8001IY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8001IY#PBF: a 5 A buck feeding five 1.1 A linear rails in one 15 mm package

The LTM8001IY#PBF is a 36 V input module that puts a 5 A step-down regulator and an array of five 1.1 A linear regulators in a single 15 mm by 15 mm by 3.42 mm ball grid array. The buck takes 6 V to 36 V in and delivers 1.2 V to 24 V at 5 A, and three of the five linear rails are fed from that buck output while the other two are fed from a separate undedicated input. The rail count is what sells the part, and the dissipation inside the package is what limits it.

Published values

ParameterValue
Input voltage, buck6 V to 36 V, 40 V absolute maximum on the buck input
Buck output1.2 V to 24 V at 5 A
Linear railsfive outputs, 1.1 A each, 0 V to 24 V, parallelable
Linear input groupingthree from the buck output, two from a separate input
Output noise90 uV RMS from 100 Hz to 1 MHz
Current limit accuracy10 percent, adjustable, constant current constant voltage
Reference2 V
Thermal resistance16.1 degree C per W
PackageBGA, 15 mm x 15 mm x 3.42 mm
Weight1.8 g
Typical switching frequency350 kHz in the front page application
Terminal finishSnPb or RoHS

Three linear rails from one buck output is where the heat goes

Take a 3.3 V buck output feeding three linear rails at 1.2 V and 1.1 A each. Each regulator drops 2.1 V at 1.1 A, which is 2.31 W, and three of them are 6.93 W inside the package. At 16.1 degree C per W that is 112 degree C of rise, so a 40 degree C ambient puts the junction near 152 degree C, which is past any grade of this part. The same three rails at 1.8 V out drop 1.5 V and dissipate 1.65 W each, 4.95 W total, which is a 80 degree C rise: that fits a 45 degree C ambient and does not fit a 60 degree C one.

That comparison is the whole selection method for this module. It is not chosen for the buck, which is an ordinary 5 A converter; it is chosen when several low voltage rails have to come from one place and the drop across each linear stage is small. A rail that has to go from 3.3 V to 0.9 V at 1.1 A belongs on a switching regulator rather than on this array, and the arithmetic above is the reason.

The two rails on the separate input can be fed from anywhere

The fourth and fifth linear regulators are tied to an input that is not the buck output, so they can be fed from the main rail, from a lower rail, or from a filtered version of either. That is what makes the module useful for a mixed signal board: the analog rails can run from a quiet pre regulator while the digital rails come off the buck, and the two groups stay separated inside the package.

The 90 uV RMS noise figure from 100 Hz to 1 MHz belongs to the linear outputs, and it is set by the reference and the loop rather than by the input. Feeding a linear rail from the buck output still passes the buck's ripple through at the rejection ratio of the linear stage, so the input capacitor at the LDO input pins is doing real work even though the current is only 1.1 A per rail.

The 2 V reference and the 10 percent current limit

Every linear output is set by its own resistor against a shared 2 V reference, and the current limit is programmed by an analog voltage with 10 percent accuracy in constant current constant voltage mode. That combination makes the part a battery charger or a laser bias supply as well as a rail generator, and the 10 percent figure is the one to put in the tolerance stack: a 1.1 A limit can be 990 mA or 1.21 A, so a load that needs 1.15 A is not guaranteed to start.

The buck side keeps its own protection and its own current limit, and the two are independent. A short on one linear output pulls that rail into current limit without touching the buck, which is the behaviour a hot swap or a plug in module needs, and it is the reason the array exists rather than five separate regulators with five separate input capacitors.

Sourcing notes for this family: the power management cross reference holds the cross references, OEM procurement is the pre substitution check, and component lead time solutions is what we use when the part on the drawing is not on the shelf.

Two questions buyers ask

Can all five linear outputs be paralleled? Yes, the data sheet states the five 1.1 A outputs are parallelable, which gives up to 5.5 A on one rail if they share the same input. The dissipation then concentrates in one place rather than spreading across five loads, so the thermal arithmetic has to be redone for the combined current rather than assumed from the single rail case.

Is the 24 V output range on the buck or on the linear rails? Both, but not at the same time. The buck output range is 1.2 V to 24 V and each linear output is adjustable from 0 V to 24 V, and the linear output has to sit below its own input by the dropout. A 24 V linear rail needs an input above 24 V, which the 36 V input allows, but at 1.1 A that is more than 20 W of dissipation and outside the package.