Contact Us

LTM4651EY#PBF

Brand: Analog Devices
Analog Devices LTM4651EY#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM4651EY#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM4651EY#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM4651EY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM4651EY#PBF: the E grade of the inverting module, and the current curve behind the 4 A headline

The LTM4651EY#PBF is the E grade of the 58 V inverting module in the 15 mm by 9 mm by 5.01 mm ball grid array. It makes a negative output from minus 0.5 V to minus 26.5 V at up to 4 A, meets EN55022 Class B radiated emissions and holds plus or minus 1.67 percent of total dc error over minus 40 degree C to 125 degree C. The 4 A figure is the top of the current range at the bottom of the voltage range, so the first thing to settle on this part is not the grade but the output current the actual voltage allows.

Published values

ParameterValue
Input voltage3.6 V to 58 V
Output voltageminus 0.5 V to minus 26.5 V
Output currentup to 4 A, derated with output magnitude
Output power24 W at 12 V in to minus 24 V out
Safe operating areainput plus output magnitude, 58 V maximum
Switching frequency250 kHz to 3 MHz, 400 kHz default
DC output errorplus or minus 1.67 percent
Radiated emissionsEN55022 Class B
Thermal resistance20.8 degree C per W
E grade rangeminus 40 degree C to 125 degree C
PackageBGA, 15 mm x 9 mm x 5.01 mm
Current sharingparallelable with multiple modules

The output current curve falls because the switch current does

An inverting converter passes the output current through the inductor during the on time as well as the off time, so the switch current is the sum of the input and output currents rather than one of them. At minus 24 V and 1 A from a 12 V input, the inductor carries roughly 3 A on average, which is why the 4 A figure belongs to minus 3.3 V or minus 5 V and not to minus 24 V. The 24 W limit and the switch current limit arrive at the same place from two directions, and the lower of the two is the answer.

The data sheet prints an output current capability curve against output voltage, and it is the only honest way to size the load. A build that needs 2 A at minus 12 V from a 12 V input is at 24 W and is exactly on the vendor's stated condition, including its airflow: 200 linear feet per minute at 60 degree C ambient. A build that needs the same 2 A with no airflow has to come down in power or accept a lower ambient.

Twenty point eight degrees per watt makes the loss budget the real limit

At 5 W of loss the rise is 104 degree C, so an 85 degree C ambient is impossible and a 60 degree C one needs the airflow the vendor specifies. A build with a 3 W loss has a 62 degree C rise and works at 60 degree C ambient in still air. That is the number to work to: three watts, which at 24 W out is 89 percent efficiency, and the part is at 82.8 percent in the vendor's condition.

For a lower power rail the arithmetic relaxes quickly. Minus 12 V at 0.5 A is 6 W out, about 1.2 W of loss and a 25 degree C rise, which is comfortable anywhere. The part is therefore used either as a small negative rail with plenty of margin or as a 24 W rail with a thermal solution, and the middle of that range is where the engineering work happens.

Ground referenced control pins and a 400 kHz default

RUN, PGOOD and CLKIN are referenced to ground on this module, which is unusual for an inverting regulator and means no level shifting is needed between the negative rail and ordinary 3.3 V logic. The soft start is programmable, the power good output is open drain and the module can be synchronized to an external clock between 250 kHz and 3 MHz, with 400 kHz as the resistor default.

The E and I order codes are both listed at minus 40 degree C to 125 degree C, so the suffix is a guarantee decision rather than a wider window on this part. What is not shared is the safe operating area: input plus output magnitude is 58 V on both, and a 48 V rail therefore carries only 10 V of negative output regardless of which grade is fitted.

Sourcing notes for this family: the power management cross reference holds the cross references, OEM procurement is the pre substitution check, and component lead time solutions is what we use when the part on the drawing is not on the shelf.

Two questions buyers ask

Does a negative output need a special inductor? It needs an inductor rated for the full switch current, which in an inverting topology is the sum of the input and output currents rather than the output current alone. The module has its inductor inside, so the external components are the input and output capacitors and the frequency resistor, and the current that matters for those capacitors is the ripple at the switching frequency.

Can two modules be paralleled for more current? Yes, the part supports parallel and current share operation across multiple modules. The practical limit is the safe operating area rather than the current: two modules in parallel double the current but do not change the 58 V rule, so the output voltage is still capped by the input rail.

The frequency resistor sets the ripple, and the default is a compromise

The module runs at 400 kHz with the frequency resistor at its default and can be set anywhere from 250 kHz to 3 MHz or synchronized to an external clock. A lower frequency means a longer on time, which in an inverting regulator means a larger inductor current swing at the same output current, so the input and output capacitors see more ripple. A higher frequency means a smaller swing and more switching loss in the same package that is already at 20.8 degree C per W.

For a rail at minus 24 V and 1 A from 12 V the default 400 kHz is the sensible middle: the on time is 1.67 microseconds, the switch current is about 3 A average, and the loss lands near the vendor's 5 W figure. A build that needs the smallest possible board area moves up to 1 MHz or 2 MHz and accepts the extra loss; a build that needs the lowest loss moves down to 250 kHz and pays for it in capacitor volume. Both are legitimate, and neither changes the 58 V rule.