LTM4650IY-1A#PBF
Product Specifications
LTM4650IY-1A#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM4650IY-1A#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM4650IY-1A#PBF: 0.8 percent of dc error on a 1 V rail, and the 3 percent transient behind it
The LTM4650IY-1A#PBF is the A accuracy grade of the dual 25 A or single 50 A module in the 16 mm by 16 mm by 5.01 mm ball grid array. It holds plus or minus 0.8 percent of total dc output error over line and load, and plus or minus 3 percent of transient error provided the minimum output capacitance is fitted. Six modules can share a rail for 300 A. The two accuracy figures are the reason the part exists, and both of them are conditional: the dc figure is over line and load, and the transient figure belongs to a specified capacitor bank.
Published values
| Parameter | Value |
|---|---|
| Input voltage | 4.5 V to 15 V |
| Output voltage | 0.6 V to 1.8 V |
| Output current | dual 25 A or single 50 A |
| DC output error, A grade | plus or minus 0.8 percent over line and load |
| DC output error, B grade | plus or minus 1.5 percent |
| Transient output error | plus or minus 3 percent with the minimum output capacitance |
| Current sharing | up to six modules, 300 A |
| Remote sense | differential amplifier |
| Compensation | external, per channel |
| Thermal resistance | 7 degree C per W |
| Package | BGA, 16 mm x 16 mm x 5.01 mm |
| Weight | 3.5 g |
Zero point eight percent of 1 V is 8 mV, and 3 percent transient is 30 mV
Eight millivolts on a 1 V rail is the dc budget, and 30 mV is the transient budget. A load step from 0 to 25 A that moves the rail 30 mV is asking the output capacitor bank to supply the difference for the time the loop takes to respond, so the capacitor value and its equivalent series resistance are part of the specification rather than a tuning choice. The vendor states the transient figure against a minimum output capacitance, which means a build with less capacitance does not have the 3 percent claim.
The A and B grades differ by 0.7 percent of dc error, which on a 1 V rail is 7 mV. That difference is a real part number decision: a rail that feeds a core with a plus or minus 3 percent requirement can take the B grade, and a rail that feeds an analog supply with a plus or minus 1 percent requirement needs the A grade. The price difference between the two is usually smaller than the cost of a re spin.
Fifty amps at 1 V is 50 W in 256 square millimetres
The package is 16 mm by 16 mm, or 256 square millimetres, and at 50 A and 1 V the output is 50 W. At 88 percent the loss is 6.8 W, which at 7 degree C per W is a 48 degree C rise. That is 195 mW per square millimetre through the ball array, so the copper under the module is the thermal solution. Two ounces of copper with a via field under the power balls behaves very differently from one ounce with a plane cut by signal traces.
At 300 A across six modules the same arithmetic applies per module, and the sharing accuracy between modules becomes a thermal question as much as an electrical one: the module that carries more current runs hotter, and its own current sense drives it back, so the loop needs the share bus to be connected and the compensation in each module set for the paralleled case.
The 15 V input maximum is the constraint on a 12 V rail
A 12 V rail at plus ten percent is 13.2 V, which is inside the 15 V maximum with 1.8 V of margin, and a 12 V rail with a transient is not. Twenty five amps at 1 V from 5 V in is a 20 percent duty cycle and 12.5 A of input at 88 percent, which is a different thermal case from the same output at 12 V in.
The output range stops at 1.8 V, so this module is for core and memory rails rather than for 3.3 V or 5 V. A board that needs 3.3 V at 50 A uses a different member of the family, and the 0.8 percent accuracy claim does not carry across the range: each part is specified at its own output window.
Buyers usually arrive at the power management cross reference to find the family alternatives, then use the ADI second source page to confirm a substitute before it is fitted; component lead time solutions is the routine for a part that has already stopped shipping.
Two questions buyers ask
Is the 3 percent transient figure available without extra capacitors? No. The data sheet states the transient error against a minimum output capacitance, and a build with a smaller bank has a larger deviation. The capacitor value, its equivalent series resistance and the external compensation together set the transient, so the number cannot be read across to a different bank.
What is the difference between the -1A and -1B order codes? The A suffix is the 0.8 percent dc accuracy grade and the B suffix is the 1.5 percent grade, with the same body, ballout and current rating. The choice is made from the load tolerance requirement, and the price difference is usually small enough that the A grade is taken when the rail feeds anything analog.
At 4.5 V in the input current is the connector rating
Fifty amps at 1 V is 50 W, and at 88 percent the input power is 56.8 W. From 12 V that is 4.7 A, and from 4.5 V it is 12.6 A, which is nearly three times the current for the same output. The module is rated to 4.5 V in, so a 5 V rail feeding it is inside the specification, but the connector, the input capacitor ripple rating and the trace width all have to be sized for the 4.5 V case rather than the 12 V one.
The input capacitor is where this shows first. At 12.6 A of average input with a 20 percent ripple the capacitor sees 2.5 A of alternating current at the switching frequency, and a small ceramic in a 5 V build is often chosen for its capacitance rather than its ripple current. A rail that works on the bench from a lab supply at 12 V and fails in the product on a 5 V backplane is usually this number.