LTC6813HLWE-1#3ZZTRPBF
Product Specifications
LTC6813HLWE-1#3ZZTRPBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTC6813HLWE-1#3ZZTRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
LTC6813HLWE-1#3ZZTRPBF: Eighteen Cells Measured to 2.2 mV, and 200 mA of Balancing That Has to Go Somewhere
The LTC6813HLWE-1#3ZZTRPBF is a multicell battery stack monitor that measures up to 18 series connected cells over a 0 V to 5 V cell range, with 2.2 mV maximum total measurement error. All 18 cells are converted in 290 us by a 16-bit delta sigma converter with a programmable third order noise filter, and voltage and current are measured synchronously. Communication is isoSPI at 1 Mbps over a single twisted pair up to 100 meters, the daisy chain is bidirectional so a broken wire in the chain is detected rather than silently cutting the stack in two, and the part is AEC-Q100 qualified for automotive use. Passive balancing sinks up to 200 mA per cell with programmable pulse width modulation, nine general purpose inputs cover thermistors and other sensors, the part can act as an I2C or SPI master to peripherals on the cell side, sleep current is 6 uA, and the body is a 64-lead eLQFP.
A battery monitor has two jobs that pull in opposite directions: measure accurately while the pack is under load, and burn off charge from the strongest cells. The first job needs a quiet reference and a filter that rejects the switching noise of the inverter. The second job puts heat inside the same enclosure as the cells.
2.2 mV is 0.067 percent of a 3.3 V cell, so a 5 mV balance threshold is measurable
On a nominal 3.3 V lithium cell, 2.2 mV is 0.067 percent. On a 5 V cell it is 0.044 percent. That error budget is what decides how closely the pack can be balanced: a balancing strategy that stops at a 5 mV spread is asking the monitor to resolve a difference smaller than twice its own error, which means the loop will hunt. A 10 mV or 15 mV threshold is inside the measurement and is where most automotive balancing strategies sit.
The 290 us for the whole stack is 16.1 us per cell, and the filter setting that gives the lowest noise is the one that stretches that window. In a pack that is being charged at high rate, the sampling window is chosen against the switching noise of the charger, and the delta sigma filter is the tool that buys rejection at the cost of time.
200 mA of balancing at 3.7 V is 0.74 W per cell and 13.3 W across all eighteen
Balancing current flows through an external resistor, not through the monitor, so the heat lands on the board next to the cells. One cell at 200 mA and 3.7 V dissipates 0.74 W, and a pack that balances all 18 at once is dissipating 13.3 W inside a sealed enclosure. The pulse width modulation exists precisely so the duty cycle, not the peak current, sets the average heat, and the resistor is chosen for the peak current while the thermal path is chosen for the average.
Balancing also runs the cells down, so the energy is lost rather than moved. In a 60 kWh pack a 200 mA balance on one cell for an hour removes 0.74 Wh, which is small against the pack and large against a cell that is already at the bottom of its charge.
6 uA of sleep current is 52.6 mAh over a year, and a parked vehicle notices
Sleep current of 6 uA drawn continuously for a year is 52.6 mAh. Against a 60 Ah pack that is 0.09 percent, which sounds negligible until the vehicle sits for six months and the monitor is one of a dozen always-on loads sharing the same budget. The part also has a wake-up path through the isoSPI interface, so the host can leave the monitor asleep between measurements rather than keeping it in a low power measuring state.
The 100 meter twisted pair limit is a cable length, not a data rate claim. At 1 Mbps the message for 18 cells plus status is a few hundred bits, and the propagation delay over 100 meters at roughly 5 ns per meter is 500 ns one way, which is the number to use when the daisy chain response time is budgeted.
| Function | Multicell battery stack monitor, 18 cells in series, AEC-Q100 qualified |
| Measurement error | 2.2 mV maximum total, 0.067 percent of a 3.3 V cell |
| Cell range | 0 V to 5 V, 16-bit delta sigma with programmable third order filter |
| Conversion time | 290 us for all 18 cells, 16.1 us per cell |
| Communication | isoSPI at 1 Mbps, single twisted pair up to 100 m, bidirectional daisy chain |
| Balancing | 200 mA maximum per cell with pulse width modulation, 0.74 W per cell at 3.7 V |
| Inputs | Nine general purpose digital or analog inputs, I2C or SPI master |
| Sleep current | 6 uA, 52.6 mAh over a year |
| Package | 64-lead eLQFP, order code HLWE-1 with the tape and reel suffix |
| Lifecycle | In production at the vendor |
Two questions buyers ask
Does the bidirectional daisy chain replace the redundant wiring of a ring topology?
It gives the fault detection of a ring with the wiring of a chain. If a wire breaks, the host can talk to the far side through the other end of the chain, which keeps the pack observable instead of losing half the cells. The pack still reports a fault and still needs service; what it does not do is go blind on the far side of the break.
Can the nine general purpose inputs be used for current measurement?
They are analog inputs with the same converter behind them, so a shunt amplifier output can be read, and the part synchronises that reading with the cell voltages. The accuracy of the current channel is then set by the external amplifier and the shunt, not by the monitor, and the synchronous sampling is what makes power computed from the two readings meaningful.
Ordering and supply
The LWE suffix is the eLQFP body, the -1 is the silicon revision and the trailing suffix is the packing. The same family covers 12 and 15 cell versions on the same interface, so a pack that changes cell count does not change the software stack.
We hold this monitor for battery and automotive builds. The analog mixed signal ICs page lists the families we carry, power management cross reference is where a pack monitor from another vendor is compared against this one, and where a pack program is moving from prototype to production, BOM shortage recovery covers how we handle a part that ships from allocation.
Request Quote — In Stock, 100% New & Original, Full Warranty