Contact Us

LTC3786EUD#TRPBF

Brand: Analog Devices
Analog Devices LTC3786EUD#TRPBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTC3786EUD#TRPBF — Analog & Mixed-Signal ICs | Superb Automation

LTC3786EUD#TRPBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTC3786EUD#TRPBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LTC3786EUD#TRPBF: A Synchronous Boost That Starts at 4.5 V and Holds 60 V Out

The LTC3786EUD#TRPBF is a synchronous boost controller that drives all N-channel power MOSFETs from a 4.5 V to 38 V input, 40 V absolute maximum, with an output up to 60 V. After start-up it can run from an input as low as 2.5 V when it is biased from the output or another auxiliary supply. The reference is 1.2 V at plus or minus 1 percent, current sensing is by sense resistor or inductor DCR, the controller reaches 100 percent duty cycle for the synchronous MOSFET, no-load quiescent current is 55 uA, shutdown is below 8 uA, the switching frequency is 50 kHz to 900 kHz programmable or 75 kHz to 850 kHz phase lockable, and there is an internal 5.4 V LDO for the gate drive. The package is a 16-pin 3 mm by 3 mm QFN or an MSOP, and the part is AEC-Q100 qualified.

Synchronous rectification is what separates this from the diode boost circuits it replaces. The rectifier becomes a MOSFET with a few milliohms instead of a Schottky with a few tenths of a volt, so at 60 V out and several amps the difference is tens of watts of heat that no longer has to leave the board.

1 percent of a 1.2 V reference is 12 mV, and the divider is on top of it

The reference tolerance of 1 percent on 1.2 V is 12 mV. A 60 V output set by a divider from that reference multiplies the error by the divider ratio, which is 50 to 1, so the reference term alone is 600 mV at the output before the resistors contribute anything. Two 1 percent resistors in the divider add more than the reference does, and a 0.1 percent pair is what a 1 percent output specification actually requires. That arithmetic is the same for every boost controller and is the reason a precision output starts with the divider and not with the part.

The 2.5 V operating floor after start-up is the cold start feature: a system that has to run from two alkaline cells at end of life can start on 4.5 V and continue down to 2.5 V once the output is up and biasing the controller. Starting at 2.5 V is not supported, and a product that expects it will fail on the bench.

60 V out from 4.5 V in is 13.3 to 1, and the duty cycle is 80 percent

A boost from 12 V to 60 V runs at an ideal duty cycle of 80 percent, which leaves 20 percent of the period for the rectifier and the dead time. The 60 V output from the 4.5 V minimum input is a 13.3 to 1 ratio, a duty cycle of 92.5 percent, and at that point the minimum off time of the controller and the turn-off delay of the FET are the limits rather than the current. The 38 V input rating with 40 V absolute leaves only 2 V of transient headroom, the tightest margin in this family, so an automotive input with a load dump needs a clamp in front of it.

Quiescent current of 55 uA over a year is 481.8 mAh, and shutdown below 8 uA is 70 mAh, so a battery powered instrument that sleeps most of the time sees the boost controller as a rounding error next to the load. The 100 percent duty cycle capability matters at the other end: when the input rises to the output level the synchronous FET stays on instead of the controller dropping out of regulation.

FunctionSynchronous boost controller, all N-channel MOSFETs
Input4.5 V to 38 V, 40 V absolute, 2.5 V after start-up with bias
OutputUp to 60 V, a 13.3 to 1 ratio from the minimum input
Reference1.2 V at plus or minus 1 percent, 12 mV before the divider
Quiescent55 uA, 481.8 mAh a year, shutdown below 8 uA
Current sensingSense resistor or inductor DCR
Frequency50 kHz to 900 kHz programmable, 75 kHz to 850 kHz phase lockable
Gate driveInternal 5.4 V LDO
Duty cycle100 percent for the synchronous MOSFET
Package and grade16-pin 3 mm by 3 mm QFN or MSOP, AEC-Q100

Two questions buyers ask

Can it boost from a single lithium cell?
Starting from 3.0 V it can, because the start-up floor is 4.5 V only until the output is established; a cell that starts near 4.2 V boots the controller and then the bias from the output carries it down to 2.5 V. The practical limit is the input current, not the controller: a 60 V output at 100 mA draws over 1.3 A from a 4.5 V input before efficiency, and the inductor and the FET have to be sized for that.

Is the 40 V absolute maximum enough for a 24 V battery system?
A 24 V lead acid system charges at 28.8 V and can see transients well above that, so 40 V absolute is the minimum and a clamp is required. A 24 V rail at plus 10 percent is 26.4 V, which leaves 13.6 V of headroom for a clamped transient and very little for an unclamped one.

Ordering and supply

The EUD suffix is the 16-pin 3 mm by 3 mm QFN body on the industrial grade, and TRPBF is tape and reel, lead free. The MSOP body is a separate suffix in the same family of twenty part models, so the package is read from the code. The grade and the qualification are separate columns on the order, and an automotive build needs both.

We supply this family for production and for repair. Start at the analog mixed signal ICs family page, compare a candidate against the power management cross reference, and where a boost stage is being re-costed, the arithmetic in how to reduce component cost covers the inductor and the FET as well as the controller.

Request Quote — In Stock, 100% New & Original, Full Warranty